Address
宁波研发园A区2栋12B17
聚贤街道,鄞州区,宁波市,浙江中国
Work Hours
周一 to 周五: 8:30AM - 10:30PM
周六 to 周日: 9:30AM - 10:30PM

TP20 styli use M2 threads, but thread size alone doesn't determine accuracy. This guide explains how to choose ball diameter, shaft length, and extensions to avoid bending errors.
“Hey, which stylus should I use with my TP20? Can I just grab any M2 and screw it on?”
In the workshop, you hear this almost every week. The operator holds a stylus, sizes it up against the probe head, and finally tightens it by feel — it works, but whether the numbers it produces are accurate is anyone’s guess. It’s only when the workpiece goes out of tolerance and the CMM report shows unexplained deviations that they start to wonder if the stylus was the wrong choice.
The TP20 is one of the most common trigger probes, and its threaded interface is locked to the M2 standard. But “M2” only tells you the thread size — it’s far from the whole story. With the same M2 thread, you can get stylus tips from 0.5 mm to 3 mm in diameter, stem lengths from 10 mm to 20 mm, and stem materials ranging from ruby balls on stainless steel to tungsten carbide. Add extension bars and stylus kits, and the official catalogue lists dozens of combinations. Each combination gives you a different measuring depth, rigidity, and bending risk. Choose wrong, and at best the stylus stem rubs against the workpiece and causes false triggers; at worst, the entire measurement result shifts systematically.
This article addresses the gap between “knowing the thread” and “choosing the right stylus”. We start with why the TP20 is locked to the M2 thread standard, and clarify the logic that the thread follows the probe, not the machine brand. We then break down the selection trade-offs along three lines: ball diameter and shaft length, shaft material and construction, and extension bars and stylus kits. Finally, we cover an easily overlooked cost—bending and measurement errors caused by excessive overhang. After reading, you will be able to answer at least three questions: What ball diameter should I use for my TP20? What shaft length keeps errors under control? Can I add an extension bar, and if so, how long is the limit? These decisions are not based on feel, but on the specification fields and selection principles in the official catalogue.
The first step in stylus selection for a CMM is not ball diameter or shaft length—it is the thread. The thread is the mechanical interface between the stylus and the probe head. If the interface is wrong, everything else is irrelevant. The thread standard is not determined by the machine brand or model; it is determined by only one thing: the model of the probe module mounted on the probe head.
Taking Renishaw’s official stylus catalogue as an example, it is split into separate volumes by thread size: M2, M3, M4, M5, plus a dedicated chapter for Faro articulated arms. Each volume’s introduction clearly states which probes it covers. The M2 volume is officially described as “for the industry-standard CMM probes TP2, TP20, TP200 and REVO™”. In other words, if your probe is a TP20, the stylus thread is fixed at M2 — there is no alternative.
A common misconception here: many people say “I have a CMM from brand X” and then look for styli by brand. But the thread follows the probe, not the machine brand. Many domestic CMM brands and some Mitutoyo models use Renishaw-style probe heads and controllers, so with a TP20 head the stylus is M2. Conversely, if a different probe head is fitted on the same machine, the thread may change accordingly. So the correct order is: first identify the probe head/probe type, then determine the thread, and only then consider ball diameter and stem length.
Why does TP20 use M2? The catalogue’s structure explains this: the M2 volume covers industry-standard trigger probes, and TP20 is one of the most widely used modular trigger probes in that group. The M3 volume covers a different set of probes — manual CMM probes TP1 and TP6, plus scanning probes SP25M and REVO™. The M4 volume is for the high-accuracy TP7M and machine-tool probing probes. The M5 volume is reserved for the highest-accuracy scanning probes. Each volume’s styli are matched to its probes in shank diameter, length range and load capacity, so the thread size is effectively guiding you to the right selection range.
On the shop floor, there is a quick way to tell: unscrew the stylus from the probe and check the thread diameter at the mounting end. The M2 thread is visibly smaller than the M3, so the two are easy to tell apart by eye. If you have a stylus catalogue handy, go straight to the trigger-probe section: in Hexagon’s “Styli and Accessories” catalogue, styli for trigger probes are grouped by M2, M3 and M4. M2-thread styli and accessories cover pages 14–21, M3 covers pages 26–30, and M4 takes only page 32. The page count does not mean one system is more important than another, but it does show how widely M2 is used in trigger-probe applications.
Another type of equipment deserves special attention: the Equator comparator. Its stylus thread is determined by the installed probe module, not by the machine model. With a TM25-20 module (fitted with a TP20 trigger module), use M2 styli; with an SM25-2 scanning module, use M3 styli. On the same comparator, changing the module changes the thread. This again shows that identifying the module is more reliable than identifying the machine.
Another common point of confusion: the M2 catalogue covers not only straight styli, but also disc styli, star styli, stylus extension bars, stylus accessories and stylus kits. In other words, once you confirm that TP20 corresponds to M2, all subsequent selections—ball diameter, stem length, extension bar combinations—should be made within the M2 catalogue. Do not pair TP20 with styli from the M3 catalogue; the threads will not match and the stylus will not fit.
Finally, one principle worth stressing: if the equipment is a domestically made CMM or a non-Renishaw brand, but the probe module is TP20, the stylus thread is still M2. Do not doubt this simply because the machine brand differs. Thread specifications are an industry-standard interface convention, not a proprietary definition of any single brand. Conversely, if the equipment is a Renishaw brand but fitted with a probe from another system, the thread may not be M2. The only basis for judgment is the probe model, not the brand name on the nameplate.
Check the actual machine configuration first. Remove the stylus and inspect the thread, or look up the probe head module model, then open the corresponding section of the manual. Getting this step right is what makes the later choices of stylus ball diameter, stem length, and material meaningful.
Straight styli in the M2 thread section cover ball diameters from 0.5 mm to 3 mm and overall lengths from 10 mm to 20 mm or longer. The range looks small, but picking the wrong step can shift your measurements by several micrometres. Keep one guiding rule in mind when selecting: ball diameter is set by the size and shape of the feature being measured, while stem length is set by the depth and accessibility of the measuring position. The two are not chosen independently — stem length decides how deep you can reach, and ball diameter decides whether you can measure accurately at that depth.
0.5 mm ball: the go-to choice for small holes and narrow slots
A 0.5 mm ball is a special option in the M2 section. The official catalogue includes a stepped stylus listed as M2-Stylus - Stepped (R-0.5-TC-0.32/0.7-L10), part number A-5000-7805 (Hexagon equivalent 03969220). Breaking that down: 0.5 mm ruby ball, tungsten carbide stem, stem diameter stepping from 0.7 mm at the mounting end down to 0.32 mm at the ball end, overall length 10 mm.
Why is a 0.5 mm stylus tip paired with a stepped rod? Because if a 0.5 mm tip is mounted directly on a 0.7 mm rod, the diameter difference between the tip and the rod is only 0.2 mm. When the tip enters a hole with a slightly larger bore, the rod can easily contact the hole wall first, causing false triggers. The stepped rod reduces the rod diameter at the tip end to 0.32 mm, increasing the clearance between the tip and the rod to 0.18 mm, so the tip can truly “reach in” and measure the bottom of the hole or groove.
On-site assessment: If the bore you need to measure is between 0.8 mm and 1.2 mm and the hole has some depth, a 0.5 mm tip is one of the few viable options. However, note that the smaller the tip diameter, the higher the sensitivity to workpiece surface roughness—a 0.5 mm tip contacts only a very small local area, and if the surface has micro-irregularities, the measured values will fluctuate more than with a larger tip. So wherever a 1 mm tip can be used, do not voluntarily step down to 0.5 mm.
Ball diameter 1 mm: “Standard starting point” in the M2 volume
The 1 mm tip is one of the most common specifications in the M2 volume. The official cross-reference table lists two typical 1 mm ball straight styli:
M2-Stylus (R-1-SS-0.7-L10) Order number A-5000-7806 (Hexagon 03969201): Ruby ball 1 mm, stainless steel rod 0.7 mm, total length 10 mm.M2-Stylus (R-1-TC-0.7-L20) Order number A-5000-7808 (Hexagon 03969221): Ruby ball 1 mm, tungsten carbide rod 0.7 mm, total length 20 mm.It is interesting to compare these two styli side by side: the ball diameter and shaft diameter are identical, and the only differences are the shaft material and overall length. The 10 mm version uses a stainless steel shaft, while the 20 mm version uses a tungsten carbide shaft. This reflects a general rule for shaft material selection: tungsten carbide is preferred for small shaft diameters of 1 mm or less. Beyond 30 mm in length, the weight of tungsten carbide becomes a concern, but at 20 mm, its rigidity advantage outweighs the weight penalty.
For on-site evaluation: measuring the outer diameter of a 2 mm pin or the bottom of a 1.5 mm wide slot, a 1 mm ball with either a 10 mm or 20 mm shaft will work. The choice between 10 mm and 20 mm depends on the distance from the probe mounting face to the feature being measured. If the workpiece surface is readily accessible, choose the shorter 10 mm stylus; only opt for the 20 mm version when you need to reach over a boss or into a cavity. The guiding principle is: use the shortest stylus that meets the application requirements — the longer the stylus, the greater the bending deflection and the lower the accuracy.
Ball diameter 2 mm: a common choice balancing clearance and rigidity
Two representative straight styli with a 2 mm ball are listed in the M2 catalogue:
M2-Stylus (R-2-SS-1.1-L10), part number A-5000-7807 (Hexagon 03969202): ruby ball 2 mm, stainless steel shaft 1.1 mm, overall length 10 mm.M2-Stylus (R-2-SS-1.3-L20), part number A-5000-3603 (Hexagon 03969212): ruby ball 2 mm, stainless steel shaft 1.3 mm, overall length 20 mm.Note that the stem diameter of the second stylus has been increased from 1.1 mm to 1.3 mm. With the same 2 mm ball, the stem length has been extended from 10 mm to 20 mm, so the stem diameter must be increased accordingly to compensate for the loss of rigidity. This is a very practical rule in the M2 booklet: as the length increases, the stem diameter is usually increased as well. Otherwise, the deflection of the slender stem becomes large enough to affect measurement repeatability.
Compared with a 1 mm ball, a 2 mm ball provides significantly more clearance between the ball and the stem. For example, with a 2 mm ball on a 1.1 mm stem, the difference in ball-to-stem radius is 0.45 mm — three times the 0.15 mm clearance of a 1 mm ball on a 0.7 mm stem. This greatly reduces the risk of the stem contacting the workpiece when the stylus enters a hole or slot. In addition, the larger contact area of the 2 mm ball averages out some of the effects of workpiece surface roughness, giving more stable measurement results.
On-site assessment: To measure a hole 5 mm in diameter and 8 mm deep, a 2 mm stylus tip with a 10 mm stylus is fully adequate. The clearance between the stylus and the hole wall is sufficient, and the 10 mm length provides good rigidity. If the hole depth increases to 15 mm, a 20 mm stylus is required, and the stylus diameter automatically increases to 1.3 mm. In this case, you must verify that the hole diameter allows the 1.3 mm stylus to pass through. A 5 mm hole is fine, but if the hole is only 3 mm in diameter, the 1.3 mm stylus with a 2 mm tip leaves very little clearance. At this point, you may need to reconsider the tip diameter or accept a higher risk of stylus rubbing.
3 mm stylus tip: upper limit of the M2 catalogue, for applications requiring large clearance
The representative 3 mm tip in the M2 catalogue is M2-Stylus (R-3-SS-1.5-L10), part number A-5000-3604 (Hexagon 03969203): ruby tip 3 mm, stainless steel stylus 1.5 mm, overall length 10 mm.
A 3 mm tip on a 1.5 mm stylus gives a radius difference of 0.75 mm, making it one of the largest-clearance configurations among straight M2 styli. This stylus is suitable for measuring larger-diameter holes, flat surfaces, and applications where surrounding obstacles must be avoided. However, a 3 mm tip has a trade-off: the larger the tip, the larger the minimum hole it can enter. A 2.5 mm hole cannot accept a 3 mm tip, so you would have to step down to a 2 mm or 1 mm tip.
On-site evaluation method: measure a hole 8 mm in diameter with a chamfered opening and 6 mm depth. A 3 mm stylus tip on a 10 mm stylus is a good fit — the clearance between the stylus and the hole wall is generous, so there is little risk of rubbing, and the larger tip gives stable readings. However, if the same workpiece also has a 2 mm narrow slot to measure, the 3 mm tip cannot handle it. In that case, you either switch to a 2 mm tip or fit a different stylus and recalibrate.
Selection logic for stylus tip diameter and stylus length: first set the tip diameter, then the stylus length, and finally check the stylus shaft diameter
In practice, the stylus should be selected in the following order:
First, look at the minimum size of the feature to be measured. The minimum width of the hole, slot or step determines the upper limit of the tip diameter — the tip must be able to enter the feature. At the same time, the tip should not be too small, otherwise the influence of surface roughness becomes more pronounced. The general rule is: choose the largest tip that can still enter the feature.
Third, check the stylus shaft diameter. Once the tip diameter and stylus length are set, look up the shaft diameter for that stylus in the official data sheet, and confirm that the shaft will not rub against the workpiece along the measurement path. This is especially important when measuring deep holes or deep slots — the shaft diameter is often overlooked compared with the tip diameter, yet false triggers from shaft contact are among the most common sources of measurement error on the shop floor.
A common pitfall: checking only the tip diameter and ignoring the EWL
The official specification sheet includes a field called EWL (Effective Working Length), defined as the distance from the sphere centre to the point where the stylus shaft would interfere with the feature being measured. This value determines how far the stylus ball can reach into the feature.
For example, with the same 2 mm ball, a 10 mm stylus and a 20 mm stylus may have different EWL values. If you need to measure the bottom of a 12 mm deep groove and a stylus has an EWL of only 10 mm, the ball will not reach the groove bottom before the shaft rubs against the groove wall. So when selecting a stylus, you cannot only check whether the overall length L is sufficient—you must also confirm that the EWL is deep enough. Refer to the official data sheet for exact values, but the selection rule is: measured depth ≤ EWL; otherwise, choose a longer stylus or one with a thinner shaft.
M2 stylus kit: covers common ball diameters and lengths in one set
If you prefer not to configure styluses individually, the official M2 stylus kit (Kit 1, part number 03969075, Hexagon code) is available. It includes straight styli with various ball diameters and extension bars in lengths of 5/10/20/30 mm. This kit covers common ball diameters from 1 mm to 3 mm and extension bars from short to long, making it ideal for equipment that has just been commissioned and does not yet have a fixed measurement task list. Once measurement tasks are established, streamline the configuration based on the actual features being measured and reduce unnecessary joints—because each additional joint introduces another potential point of bending and deviation.
Summary of selection logic
Choosing the ball diameter and stylus length for an M2 stylus is essentially a trade-off between three constraints: the size of the feature being measured (which sets the upper limit for ball diameter), the depth of the measuring position (which sets the lower limit for stylus length and EWL), and the clearance around the stylus shaft (which sets the upper limit for shaft diameter). Ball diameters range from 0.5 mm to 3 mm; each step up gives more clearance between the ball and the feature and more stable measurements, but also increases the minimum feature size that can be measured. Stylus lengths range from 10 mm to 20 mm; each step up improves reach, but reduces rigidity and accuracy. The final choice should always follow the official data sheet, but the decision order is always: first confirm the ball can enter the feature, then confirm the stylus can reach the measuring position, and finally confirm the shaft does not rub against the wall.
There is almost no debate about the ball material for an M2 stylus: ruby. The official position is that “there are very few applications where ruby is not suitable.” Its surface is extremely smooth and its compressive strength is high, making it suitable for the vast majority of shop-floor conditions. The real decision to be made on site is the shaft under the ball—stainless steel or tungsten carbide, with ceramic and carbon fibre shafts sometimes encountered. The shaft material determines the rigidity, weight and crash resistance of the stylus, and directly affects the stability of the data you measure.
Let’s start with the official recommended ranges for the two most common stylus materials. Stainless steel stems are used for stylus tips of 2 mm diameter or larger, with a total length not exceeding 30 mm. Tungsten carbide stems are used for small stylus tips of 1 mm diameter or less, or where the total length does not exceed 50 mm. This split is not arbitrary—it comes down to stiffness-to-weight ratio and deflection control.
The most common M2 styli in the workshop are stainless steel stems with a 2 mm stylus tip, 1.1 mm stem diameter, and 10 mm total length, plus stainless steel stems with a 3 mm stylus tip, 1.5 mm stem diameter, and 10 mm total length. Both fall into the “short and stout” category. In this size range, stainless steel offers the best stiffness-to-weight ratio and mass, making it the default choice for trigger probes. If you are measuring conventional machined parts—holes, faces, and slots within a few tens of millimetres—these two styli will cover most everyday tasks.
When should you switch to a tungsten carbide stylus? Watch for two signs: the stylus tip diameter has worn below 1 mm, or the total length needs to exceed 20 mm while the tip diameter remains very small. A typical example is a stepped stylus with a 0.5 mm tip and a 0.32/0.7 mm shaft, 10 mm long—this stylus is used to measure fine features such as small holes, narrow slots, and thread forms. A small tip diameter means a thin shaft; stainless steel lacks rigidity at thin shaft diameters, whereas tungsten carbide is harder and reduces bending during measurement. Another example is a straight stylus with a 1 mm tip, tungsten carbide shaft, and 20 mm total length—it resists deflection from long overhangs better than a stainless steel version with the same tip diameter.
One pitfall to note: tungsten carbide is significantly denser than stainless steel, so for the same shaft size, tungsten carbide is heavier. The manufacturer explicitly states that once the tungsten carbide shaft exceeds 50 mm in length, weight becomes an issue, and the joint between the shaft and the tip loses rigidity due to flexing. So don’t assume that “harder tungsten carbide is always better”—for long styli where carbon fiber or ceramic is the right choice, a stiff shaft can actually work against you.
Ceramic shafts are suitable when the stylus tip diameter is greater than 3 mm and the length exceeds 30 mm. Their rigidity is comparable to steel, but they are significantly lighter, and they shatter on impact—this is not a defect but an intentional design: the ceramic shaft breaks, leaving the probe body unharmed. If your measurement task requires a long stylus reaching into a deep cavity and you are concerned about accidental collisions, ceramic shafts are worth considering. Carbon fiber shafts are used for lengths exceeding 50 mm, offering maximum rigidity and extremely low mass, with negligible thermal expansion, making them suitable for precision measurement with long overhangs.
An on-site selection method is as follows: first check the stylus tip diameter, then measure the total stylus length, and then consult the official data sheet for the shaft diameter. If the tip diameter is 2 mm or more and the total length is within 30 mm, stainless steel shafts are the standard choice; if the tip diameter is 1 mm or less, or the total length is between 20 and 50 mm with a small tip diameter, tungsten carbide shafts are more appropriate; for lengths exceeding 50 mm, consider carbon fiber or ceramic directly. This selection sequence helps you quickly narrow down the options.
Another structural detail worth noting is the stepped stylus. You can see it in the official name M2-Stylus - Stepped (R-0.5-TC-0.32/0.7-L10), which means a 0.5 mm ruby ball, a tungsten carbide stem, and a stem diameter that tapers from 0.7 mm at the mounting end to 0.32 mm at the ball end. The stepped design keeps the section near the ball slim so it can reach into small features, while retaining sufficient stem diameter and rigidity at the mounting end. When selecting this type of stylus, confirm that the transition section will not interfere with the feature being measured — refer to the official data sheet.
The M2 thread system feels like it has “too many combinations to remember” because of the extension bars and stylus kits. In the catalogue, M2 stylus extension bars take up a full page (page 19), stylus accessories a page (page 20), and stylus kits another page (page 21). Add the stylus bodies starting on page 14, and the M2 thread alone spans eight pages. It is a lot to take in, but for equipment engineers the real decisions come down to two things: whether to use an extension bar, and whether to buy individual components or a stylus kit.
Let’s start with extension bars. Their purpose is to improve accessibility — when the probe cannot reach the bottom of a deep cavity or bore, or when the feature to be measured is obstructed by a boss, an extension bar carries the stylus further in. The M2 extension bar is available in several lengths in the catalogue; refer to the official data sheet for exact values. The first on-site rule for choosing an extension bar is: avoid it whenever possible. Renishaw’s official selection guidance repeatedly stresses “minimising the number of joints” — every connection between the stylus and the extension bar adds another potential point of bending and misalignment. This is not theoretical fussiness but a common source of error in practice: the threaded mating surfaces between the extension bar and the stylus work slightly loose after repeated assembly and disassembly, and under a slightly higher trigger force this joint can shift by a small amount, which shows up in the measurement data as degraded repeatability.
If extension is truly required, follow the decision logic in order: first confirm that the extension bar itself is rigid enough. The relationship between bar diameter and length for M2 extension bars is given in the official data sheet, but a practical rule of thumb applies on site: the longer the extension bar, the shorter the allowable stylus overhang. For example, a 30 mm extension bar with a 10 mm short stylus gives acceptable rigidity; if a 20 mm stylus is then added to the extension bar, the total overhang approaches 50 mm, and the error from bar deflection at trigger may exceed the tolerance. In this case, rather than extending further, consider changing the probe head angle or using special configurations such as disc or star styli to clear the obstruction.
The second point is the choice of stylus kit. In the catalogue, Kit 1 of the M2 stylus kit has part number 03969075 and is described as “containing multiple straight styli with various ball diameters plus extension bars of 5/10/20/30 mm length.” This combination is practical on site: one purchase covers the common ball diameters and extension lengths, so there is no need to place a rush order when a new workpiece arrives. However, the kit has its trade-off: not every extension bar in the kit will necessarily be used. A common mistake made by equipment engineers on site is to treat the stylus kit as a “complete set” and try every piece, only to find that most extension bars sit idle, which only adds to the clutter in the tool cabinet.
A more practical approach is to treat the stylus kit as a spare parts pool rather than the default configuration. When programming a new workpiece, first test with the shortest stylus; if the target feature cannot be reached, then add an extension bar. The extension bar length should be chosen on a “just enough” basis, without leaving extra stock allowance. The 5/10/20/30 mm lengths in the stylus kit correspond to the four common overhang requirements on site, but which one to use depends on the depth of the feature being measured and the probe head indexing angle, subject to the actual machine configuration.
Another on-site decision point is the mixing of individual components and stylus kits. The stylus kit provides standard combinations, but actual workpieces vary widely, and there may be a need for a 15 mm extension bar—one that is not in the kit and may not be in the individual parts catalog either. In this case, do not force a fit, and never connect two extension bars in series to make up the length. Series-connected extension bars are one of the most avoided practices on site: each additional joint introduces another deviation point, and the cumulative bending error of two series-connected extension bars is far greater than that of a single bar. The correct approach is to consult the official data sheet for a closer available specification, or use an adaptor from the stylus accessories to adjust the spatial orientation.
Stylus accessories (page 20) are often overlooked when planning combinations, but they are the key to solving problems such as “can reach, but wrong angle”. These accessories include centres and knuckle joints. The knuckle joint provides two-axis, omnidirectional adjustment for probing inclined features, and is especially useful when the probe or probe head cannot be easily reoriented, or when space is restricted. The rule for deciding whether to use a knuckle joint on the shop floor is simple: if rotating the probe by one angle solves the problem, do not use a knuckle joint; only consider one when reorientation would crash into the workpiece or fixture. The knuckle joint is itself a movable interface, so its rigidity is lower than that of a one-piece stylus. This is a structural characteristic, not a quality defect.
Back to the stylus kit itself. In the catalogue, the description of Kit 1 in the M2 stylus kit mentions “includes various ball-ended straight styli”. For the specific combinations of stylus tip diameter and shaft length, refer to the official data sheet. When a shop-floor engineer receives a stylus kit, the first step is not to file each stylus by part number, but to regroup them by workpiece type. For example, group styli with Ø2 mm ruby tips and short shafts together for routine external profile measurement; store styli with Ø1 mm or smaller tips separately for small holes and narrow slots. The reason is that the stylus kit is a standard configuration, but the workpiece family on site is fixed. Reorganising styli by workpiece family reduces the time spent searching for the right stylus during programming.
To sum up the on-site selection logic in three sentences: the extension bar is a last resort, not the first choice; the stylus kit is a spare-parts pool, not a default configuration; and never connect extension bars in series—if one bar is not enough, change the setup. The M2 system offers dozens of combinations, but in practice only a few short styli plus one extension bar are used regularly. Reducing the number of combinations actually improves the stability of the measurement system.
Stylus length is most often chosen on the basis of “as long as it reaches,” but length is never just a reach issue. An overly long M2 stylus mounted on a TP20 starts building in error from the moment it is tightened.
First, consider the overhang. The total stylus length L is measured from the mounting face to the stylus tip centre. Once the thread is screwed into the probe, the distance from the stylus tip centre to the probe front face is the actual overhang. The longer the overhang, the more the stylus behaves like a cantilever beam. During measurement, the stylus tip contacts the workpiece surface, and the reaction force is transmitted through the stylus shaft to the trigger mechanism inside the probe. The longer the shaft, the greater the bending moment at the mounting end for a given contact force, and the greater the shaft deflection. The trigger probe operates on the principle of “signalling when a preset trigger force is reached”. The shaft absorbs part of the force first, so the actual displacement of the stylus tip differs from the displacement sensed inside the probe, which introduces measurement error.
The term “bending point” is repeatedly emphasized in Renishaw’s official selection guidelines: every additional joint surface introduces another potential bending and deviation point. A straight stylus is a single integral rod, so bending is distributed continuously along its length. However, once a joint is added between styli or between a stylus and an extension bar, the threaded connection becomes a point of stiffness discontinuity. At this location, both the cross-sectional moment of inertia and material continuity change, making it the most likely point for slight deflection under load. One of Renishaw’s three official stylus selection principles is to “minimize the number of joints”—every connection between a stylus and an extension bar adds one more link that can cause the stylus tip position to deviate from its theoretical value.
For the M2 catalogue specifically, the stylus kit includes 5 mm, 10 mm, 20 mm, and 30 mm extension bars; for individual extension bars, refer to the official data sheet for specifications. A common mistake on the shop floor is to connect a 20 mm extension bar to a 20 mm stylus, giving a total overhang of nearly 40 mm. At this length, the bar diameter is typically only 0.7 to 1.5 mm (per the official data sheet), so rigidity is already significantly reduced. More importantly, the two threaded joints are stacked, turning one bending point into two. If the tolerance of the feature being measured is in the micrometre range, the repeatability variation caused by this combination is often greater than the repeatability of the probe head itself.
The evaluation method is straightforward. When selecting a stylus, first check the ratio of stylus tip diameter to stylus stem diameter: the finer the stem and the larger the tip, the more length-sensitive the stylus becomes. In the M2 system, a stylus with a 1 mm tip and a 0.7 mm stem, at 10 mm total length, is the standard configuration. At the same tip diameter but 20 mm long, the slenderness ratio increases significantly, and the deflection under lateral force becomes non-negligible. Conversely, a stylus with a 3 mm tip and a 1.5 mm stem, also 20 mm long, offers much better rigidity. So “short” is not a universal rule—what matters is whether the stem diameter matches the length.
Another consideration is the measurement direction. A trigger probe is more sensitive to lateral forces (X/Y axes) than to axial forces (Z axis). The longer the stylus overhang, the greater the lever effect during lateral measurement. If the workpiece geometry forces you to use a long stylus for side contact, you must accept that repeatability in that direction will be worse than with a short stylus. In such cases, consider an alternative: use an extension bar to reach into the feature with the probe head itself, rather than relying on a long stylus. Extension bars are typically thicker than styluses of the same length (refer to official data sheets), providing better rigidity, and they introduce only one joint. This is a practical application of the “fewer joints” principle: keep the stylus short and use a stiffer extension bar to handle accessibility.
Also note the EWL (Effective Working Length) field. EWL is measured from the centre of the stylus ball to the point where the stylus stem would interfere with the feature being measured. When selecting a stylus, you cannot simply look at the overall length L; you must also confirm that the EWL is sufficient. For example, when measuring the bottom face of a deep hole with a stylus that has a 2 mm ball and a 20 mm overall length, refer to the official data sheet for that stylus to determine its EWL. If the hole depth exceeds the EWL, the stem will contact the hole wall first. In this case, the solution is not to choose a longer stylus, but one with a larger ball diameter — a larger ball increases the step difference between the ball and the stem, shifting the point of stem contact further back and thereby increasing the EWL. This is one of the reasons behind the official selection guideline of “use the largest ball possible”: increasing the clearance between the ball and the stem reduces false triggers caused by the stem rubbing against the workpiece.
Finally, a tip from the field: if the repeatability of the stylus tip position noticeably degrades during calibration, don’t suspect the probe first. Remove the stylus and gently flex the shaft by hand to check for visible elastic deformation. The M2 threaded shaft is thin, and long styli can develop slight bends during shipping, installation, or after a crash. The official catalogue lists the weight and shaft diameter for each stylus, so you can estimate rigidity when selecting. When in doubt, use the shortest stylus that meets the application and minimise the number of joints—these two rules are always safe.
Reply: Follow the probe — that is the only correct order of judgment. Thread size follows the probe model, not the CMM brand. Many domestic brands, and even some imported ones, use Renishaw components for their probe heads and controllers, so saying “I have brand XX” does not directly tell you whether to use M2 or M3. If your probe head is a TP20, then go straight to the M2 thread section. Renishaw’s official specification for the M2 section is very clear: it covers the industry-standard CMM probes TP2, TP20, TP200, and REVO. Conversely, if you see a TP6 or SP25M scanning module, you need to look in the M3 section. The judgment order is always: first identify the probe/probe head model → then determine the thread → and only then consider ball diameter and stylus length. Don’t be influenced by the CMM brand, and don’t be swayed by colleagues’ habits. The most reliable approach is to remove the probe and check the model nameplate, or consult the equipment configuration sheet.
Reply: Your thinking is on the right track, but don’t rush to replace everything—it depends on the situation. The main advantage of tungsten carbide stems is their rigidity, which suits small-diameter applications. The official guidance on stem material is clear: stainless steel stems are for stylus tips with a ball diameter of ≥2 mm and a length up to 30 mm; tungsten carbide stems are for small-diameter tips of 1 mm or less, or for lengths up to 50 mm. You’re using a 1 mm ball, which falls right within the tungsten carbide recommendation. If you notice the stainless steel stem bending noticeably during measurement or causing frequent false triggers, switching to tungsten carbide is reasonable. However, keep in mind that tungsten carbide stems over 50 mm become heavy, and the joint where the stem connects is prone to flexing and losing rigidity. So, if you need a longer stylus, consider ceramic or carbon fiber stems instead. Also, before changing the stem, check whether the stylus length itself is the issue—the first of the official selection principles is to “use the shortest stylus that meets the application.” Often, the problem isn’t the stem material but the length being excessive.
Reply: No, what you heard is an exaggerated claim. The official statement sets strict conditions for changing the stylus ball material: only when performing “heavy-duty scanning” on aluminum parts does the ruby ball suffer adhesive wear due to material attraction, causing aluminum to transfer and build up on the ball. Note the key phrase is “heavy-duty scanning”—not all aluminum measurements require a ball change. If you are using a touch-trigger probe (the TP20 is a typical touch-trigger probe), the measurement method is point-to-point contact, not continuous scanning, so the ruby ball is perfectly suitable. The official wording is “there are very few applications where ruby is unsuitable,” and ruby is the industry standard. Silicon nitride balls are an alternative for scanning probes doing continuous scanning on aluminum, but silicon nitride actually shows significant abrasive wear when scanning steel, so its applicability is narrow. Therefore, since your TP20 is a touch-trigger probe, there is no need to change the ball material for aluminum parts—just keep using the ruby ball.
Reply: Poor repeatability is most likely caused by a combination of “too many joints” and “excessive overall length”. Two of the official selection principles apply directly to your case: first, use the shortest stylus that meets the application requirements; second, minimise the number of joints — every stylus or extension bar added introduces another potential point of bending and deviation. Your current setup is an extension bar plus a stylus, giving at least two mating surfaces, and with a 20 mm stylus length, the total overhang is already considerable. The TP20 is a kinematic trigger probe and is inherently sensitive to long stylus configurations. The manufacturer explicitly states that very long stylus/extension bar combinations are not recommended for standard kinematic trigger probes, as reduced rigidity and bending lead to accuracy loss. I suggest you investigate in this order: first, see whether the stylus length can be reduced, for example from 20 mm to 10 mm; then, check whether the extension bar can be eliminated by selecting a single longer straight stylus, thereby removing one joint. If a long combination is truly necessary for deep cavities, you must verify that the stylus extension bar diameter is sufficiently large and that the stylus shank diameter matches. Refer to the official data sheet for specific parameters.
Reply: A disc stylus is specifically designed to probe positions that are difficult for star styluses and straight styluses to reach, such as internal undercuts and grooves. When selecting one, two key dimensions matter: disc diameter and disc thickness. The disc diameter determines the size of the groove you can measure, while the disc thickness determines whether the stylus can fit into narrow slots. The official naming convention example is M2 DSC SD18 SLVS T2.2 L2.6 BR-Y, which is provided only to explain the naming rules; specific part numbers and specifications are subject to the official data sheet. Several important points must be noted when using a disc stylus: first, a simple disc can only effectively probe in the X and Y directions. It essentially contacts the workpiece with its spherical edge, and the usable spherical area is very small. Thin discs must be carefully angle-aligned to ensure correct contact. Second, a simple disc only requires calibration of one diameter, typically performed in a ring gauge. Third, if Z-direction probing is required, a disc stylus with a radius-end roller must be selected, provided that the roller centre extends beyond the diameter of the probe head body; calibration can then be performed on a ball or gauge block. Additionally, some disc styluses feature a central thread that allows mounting of a centre stylus for probing the bottom of deep holes. When selecting, first ensure the disc can enter the groove smoothly, then choose the largest possible disc diameter to average out the effects of workpiece surface roughness.
Reply: Yes, ready-made kits are available. The Hexagon catalogue includes an M2 stylus kit, part number 03969075, officially named “M2 Stylus Kit 1”. This kit contains straight styli with various stylus tip diameters, as well as extension bars with lengths of 5, 10, 20, and 30 mm. In other words, once you receive it, you can assemble different stylus configurations to suit the size of the parts you are measuring on site. The kit is designed to cover common measurement scenarios: small holes with short styli and small tip diameters, deep cavities with extension bars, and general planar features with medium tip diameters. However, note that the exact number of styli and the combination of tip diameter and stem diameter for each stylus are not listed item by item in the official catalogue; you should refer to the official data sheet for details. Additionally, if you are using the Renishaw TP20 system, you can also refer directly to the Renishaw M2 brochure, which also offers stylus kit options. One point to keep in mind: the kit is a “general configuration” and may not cover all special features on your site, such as disc styli or star styli, which are typically not included in the basic kit and must be ordered separately. I suggest you first identify the 3–5 most common feature types on site, then decide whether to purchase the kit or configure individual styli.
Selecting a stylus is essentially a process of translating “measurement requirements” into “mechanical interfaces”. The selection logic for M2 threads can be condensed into a decision rule you can apply on the machine tomorrow: First determine the stylus tip diameter, then check the stylus length and trigger force direction, and finally verify the effective thread engagement depth and clearance.
In practice, follow three steps. Step one: infer the stylus tip diameter from the minimum internal diameter or groove width of the feature being measured — the tip diameter must allow the stylus to enter while keeping the shaft clear of the walls; base this on the measured feature size and official EWL data. Step two: with the tip diameter satisfied, choose the shortest possible stylus; longer stylus lengths amplify bending and deflection, and the specific effect is subject to official data sheets and measured calibration. If a long stylus is unavoidable, prefer a carbon-fibre shaft and avoid excessive trigger force in the Z-axis direction. Step three, and the most easily overlooked: before screwing in, use a thread gauge or visual inspection to check the effective engagement length of the M2 thread at the stylus base, confirming it is sufficient per the official probe head and stylus data; also confirm that after rotating the stylus, the stylus tip path will not interfere with workpiece bosses or fixtures.
If you remember only one thing on the shop floor, make it this: when stylus tip diameter and stylus length conflict, keep the stylus tip diameter and sacrifice the stylus length — the tip diameter determines contact accuracy, while the length only affects rigidity, and rigidity can be compensated by reducing traverse speed.
Finally, make it a habit: every time you change a stylus, run a 5-point calibration on a reference sphere and record the deviation in X, Y, and Z. If the deviation is clearly outside normal repeatability, don’t rush to adjust the compensation file — first remove the stylus and check the threaded face for burrs or chips. In many cases the problem is not the stylus itself but the cleanliness of the thread joint. Post this rule next to the machine; it will serve you better than any selection chart.
Every machine differs in configuration, operating conditions, and budget. This article provides only a reference framework. You can:
NINGBO JCE INDUSTRIAL TECHNOLOGY CO., LTD. — 15 years of precision measurement expertise, offering selection, installation, calibration, repair, and maintenance services for the full range of Renishaw, Marposs, and Blum-Novotest probes and tool setters.
| Contact Information | Details |
|---|---|
| Official Appointment | jcetech.cn/contact |
| Service Hotline | 157-5780-7400 / 132-2194-1413 |
| Repair Shipping Address | A2-12B17, Ningbo Yinzhou R&D Park |
| Service Coverage | Nationwide on-site support · 48-hour response for urgent repairs |
Send us your issue, and our engineers will help you work out the numbers.
If the criteria or procedures in this article do not match your machine, send us the control system, probe model and a photo of the installation — we will answer with the specific settings rather than a generic recommendation.
| Item | Detail |
|---|---|
| Company | NINGBO JCE INDUSTRIAL TECHNOLOGY CO., LTD. (JCETech) |
| Address | Room 14-1-17, Building 033, Building 2, No. 15, Lane 587 Juxian Road, Juxian Subdistrict, Hi-Tech Zone, Ningbo 315048, Zhejiang, P.R. China |
| Contact | Mr. Li / Mr. Zhang |
| Phone | +86 157-5780-7400 (Mr. Li), +86 132-2194-1413 (Mr. Zhang) |
| Online booking | jcetech.cn/contact |
Repair intake and on-site service use the same address. Please call before shipping a unit so transport and scheduling do not have to be repeated.
Probe, tool setter and laser interferometer repair, calibration and on-machine measurement integration.
157-5780-7400 / 132-2194-1413
打开微信扫一扫,关注「宁波匠测」
获取维修进度查询与技术支持
打开企业微信或微信扫一扫
添加专属顾问,随时沟通