Address
宁波研发园A区2栋12B17
聚贤街道,鄞州区,宁波市,浙江中国
Work Hours
周一 to 周五: 8:30AM - 10:30PM
周六 to 周日: 9:30AM - 10:30PM

Three-level inspection for Equator structural cracks: base casting visual and penetrant check, plate flatness measurement, and strut straightness and length.
The determination of structural component damage is to advance the three-layer inspection of “visual and tactile”, “data extrapolation”, and “disassembly inspection” in order, using the difference patterns of 10 extreme ranges at the same position and 10 extreme ranges at different positions to separate geometric deformation from the hinge point gap. The comparison uncertainty between Equator 300 and 500 is ± 0.002 mm (provided that the measurement is taken immediately after re mastering, the clamping deviation is ≤ 1 mm, and certified standard parts are used). However, once the base casting, top casting, floating platform, three drive struts, and their supporting components that undertake this level of geometry deform, no parameter compensation can be made up for.
The official component diagram of Equator (Installation and Controller Guide, shared with numbers 132816300 and 500) provides a identifiable list: 1 Base casting, 2 SP25 probe assembly, 3 Floating/moving platform, 4 Support strut, 5 Top casting, 6 Drive strut, 7 Counterbalance mechanism, 8 Upper pivot/Hooke’s joint, 9 Support arm, 11 Drive housing, 12 Parallel constraint mechanism. 13 Fixture plate, 15 Stop button.
The structural components discussed in this article are the ones that determine the geometric relationships: base castings, top castings, floating platforms, support and drive rods, support arms, and drive shells. They are the physical links of the measurement chain: the machine coordinate system is established because the relative positions of these components do not undergo measurable changes when subjected to force.
The official description of structural materials is only two words: castings, not granite. The technical specifications have also compared that traditional Cartesian structures rely on “large granite shafts/heavy castings” to maintain rigidity, which precisely introduces hysteresis and inertia problems. The rigidity of Equator comes from closed geometric constraints – thickness does not represent rigidity.
By dividing the structure into three layers, a coordinate system is established for detection. The first layer is the fixed frame: the base casting and the top casting.The base casting is the benchmark of the entire machine, carrying the drive end, support arm, and fixture plate; The top casting and the base jointly determine the relative position of the upper and lower hinge points. Both have high stiffness and brittleness: they hardly deform normally, but once plastic deformation or cracking occurs, it is often irreversible.
The second layer consists of moving parts: a floating platform and three driving struts.The platform is equipped with a probe component, and its position is determined by three straight line driven struts, which are constrained by the struts and support arms. All three driving struts are equipped with gratings, and the driving point and feedback point are of the same origin, which is the direct source of position feedback; The official component diagram lists the strut as part 4, but does not disclose whether it follows or has feedback. Both ends are Hooke hinges that only withstand tension and compression.
The third layer is the constraint points: Hooke hinge and parallel constraint mechanism.The hinge point is not a component, but the positional relationship itself: the length of the three rods is only meaningful when they match the determined hinge point position. Once there is a gap or displacement at the hinge point, the readings of the three rods remain unchanged, but the points in space change. The difficulty of diagnosis increases layer by layer, and the third layer can only be inferred from data.
During casting, uneven cooling occurs, leaving residual stresses inside; Processing and cutting off the surface material breaks the stress balance, and the component is balanced through slight deformation. The industry usually releases it in advance through aging, and the specific process is subject to the official manual. During normal operation, this part of the stress has stabilized, but it is reactivated by abnormal loads such as collision, overload, drop, forced clamping, and single point top pressure. The load pushes the local stress beyond the elastic limit, causing plastic deformation of the component; If the stress concentration zone happens to be a casting defect (porosity, shrinkage porosity, cold shut), microcracks may also occur.
Two inferences form the basis for all subsequent criteria. Firstly, damage often starts from the inside or back, and coatings and paint surfaces can mask early microcracks. Secondly, once deformation occurs, it is an error that changes with the posture: the deviation caused by the clearance between hinge points can usually be repeated, and compensation can eat up a part of it; The deviation of platform or strut deformation varies with position and probe direction, and there is no compensation value that can align the entire working volume.
The strut is slender, but its geometric shape directly participates in pose calculation: the calculation assumes that the axis of each rod is a straight line connecting the hinge centers at both ends, and the actual axis deviates, resulting in model errors between the length reading and the actual position of the platform. Straightness describes whether the axis is a straight line: the actual length of the bent rod is greater than the distance from the hinge center line, and when compressed, it first bends in the bending direction. Parallelism should be used with caution – strictly speaking, it is the relationship between two elements, and the strut itself does not have a “parallel” object; The “parallelism of struts” referred to in engineering actually refers to whether multiple struts are coordinated in the same posture, which cannot be measured on site.
The third level is not three parallel options, but a path of synchronous increase in cost, invasiveness, and information volume. The first level can only detect the damage that has already been manifested; The second level requires a baseline of data before damage to force geometric changes that are not visible to the naked eye; Once the third level is disassembled, it will face the restoration of pre tightening and geometric relationships, and the calibration conditions required for restoration are not available on site. Therefore, disassembly inspection is only carried out when both the first two levels point to the structure. The purpose is not to repair it by oneself, but to nail down the conclusion. The criterion relationship can be summarized as follows: if rejected at the first level, there is no need to go down; Passing the first level and failing the second level indicates that the damage is internal; Both levels pass, no need to dismantle.
| Level | Object of Detection | On site Methods | Form of Passing | Form Pointing to Structural Problems | Associated Risks |
|---|---|---|---|---|---|
| Level 1 | Appearance, tolerance, abnormal noise | Visual inspection, flashlight, dye penetration, light push test, listening | No signs of cracks, no empty movement, no abnormal noise | Fine lines or rust on the paint surface seeping out, light push has empty movement, one-way jamming with metallic sound | Power on test triggers motion; Residual contamination of penetrant |
| Level 2 | Repeatability and positional consistency | 10 extreme ranges at the same location, 10 extreme ranges at different locations, directional deviation | The magnitude of extreme ranges at each location is similar and comparable to the historical baseline | The difference in extreme ranges across locations is significantly amplified; Mean drift with position | Lack of baseline leads to no criteria; Temperature fluctuations are misread |
| Level 3 | Component Geometry and Fitting Surface | Disassembly and Inspection, Straightness Approximate Measurement, Installation Surface Fit Inspection | Full circumference Fit of Installation Surface, No Significant Bending of Rod | Single side Gap of Installation Surface, Rod Bending Exceeding Site Criteria | Disassembly and Assembly Changes Pre tightening and Geometric Relationship |
Reading method: Advance from top to bottom, stop when encountering rejection – If a crack is found in the first level, there is no need to test the second level. Only when the difference is amplified in the second level, consider the third level.
Visible: coating and paint surface abnormalities (blistering, cracking, localized rust exudation); Abnormal relative position of components (platform at non design angle, platform not parallel to fixture plate); Fastener displacement traces (bolt original mark misalignment, gasket extrusion).What is more important that cannot be seen: internal and back cracks, elastic deformation that automatically recovers after unloading, and hinge point gaps that are obstructed by the structure. So the first level is a sieve, not a criterion, which only indicates that there is no visible structural damage to the naked eye. Two practical requirements: wipe clean before looking, use only water or official cleaning kit for cleaning, and the official clearly prohibits the use of cleaning agents ;Illuminate diagonally with a flashlight instead of looking directly at * *. Illuminate diagonally in two directions at the same position to distinguish between genuine cracks and machined patterns.
Color penetrant testing (PT) relies on capillary action: penetrant enters the opening defect, excess is removed, and then imaging agent is applied, and the penetrant in the defect is sucked out to form a color mark. It can detect open cracks leading to the surface with higher sensitivity than visual inspection. What it cannot achieve is precisely the three things that this article is most concerned about: inability to see internal stress (by only going through the opening, the component can penetrate all qualified parts while the internal stress is close to cracking); Cannot see geometric deformation (no response to platform misalignment or pole bending); Not providing quantification (color depth is not proportional to depth).
Which surfaces are not allowed to be penetrated, which is the most prone area to accidents on site. Coating and paint surface – showing issues with the paint and contaminating the coating; Anodizing, blackening, coating – opening defects are not related to the substrate, and porous structures can also adsorb penetrating agents, causing false display of the entire piece; Clean mating surfaces, near gratings, and measurement reference surfaces – residues can contaminate the mating surfaces and grating body; The positioning surface that is about to come into contact with the workpiece or standard part – residue will affect the clamping and comparison results.
The process usually includes pre cleaning, infiltration, removal, drying, imaging, observation, and post cleaning. The time and temperature are subject to the consumables manual and relevant standards; Post cleaning is the easiest way to save, as the penetrant will be carried away by gloves after being eliminated. Compromise approach: Penetration is only reserved for situations where “suspicious thin lines have been seen and it needs to be confirmed whether they are cracks”, and it is not a census method.
Texture is the cheapest and easiest first level method to make mistakes. There are three prerequisites: power off (or emergency stop press and confirm that there is no output from the drive), confirm that the platform can move freely, and apply light force to prevent the mechanism from moving (using “fingertip push” instead of “palm push”). Action 1: Gently push the platform and feel the emptiness.Push along X, Y, and Z once each, and feel if there is a period of non force transmission between the “push” and “force”, which is called a gap; The unidirectional displacement points to the hinge point or constraint surface in that direction. Action 2: Gently rotate the platform and feel the sway.Symmetrically pushing in opposite directions with both hands, the platform can rotate slightly without moving, indicating insufficient constraints; This analogy is only used as a small auxiliary on 300, not on 500 and X-500.
Action 3: Tap the component lightly and listen for the sound.Lightly tap the base, top casting, platform, and support arm with a hardwood or plastic handle, and the sound of different parts should be similar; Sudden stuffiness is usually caused by vibration attenuation due to delamination or crack surfaces. This is a common practice in the industry and can only serve as a reminder – due to differences in casting wall thickness, the sound can only be compared horizontally with the same machine.
What can be achieved: When the power is cut off, the platform is released from the limit, and the strut is not pre tightened, use a ruler or a knife edge ruler to move along the axis against the outer circle of the strut and check whether the light transmission gap is continuous and uniform; A sudden increase or decrease in a certain section indicates that the axis of the section deviates from the straight line. This is an approximate method for determining whether there is obvious bending, but it cannot provide numerical values or distinguish slight S-shaped bending.The three things that cannot be done must be stated directly: * * Unable to provide measurement values (there is no platform, V-shaped block, or standard cylinder on site, and the values must be removed and sent to the measurement site, which already belongs to level three); Unable to measure the true axis in the assembled state (due to the combined effects of counterweight, gravity, and pre tension, different from the free state); Parallelism cannot be discussed (the three bar coordination relationship only holds in the overall posture of the machine). Conclusion: The straightness check without disassembling the machine can only exclude obvious bending and cannot confirm the absence of bending. The report should state ‘no obvious bending observed’ but not ‘straightness qualified’.
This is the technical core of the entire article, and the key lies in the way of comparison.
Range at the same position: Select a position on the fixture board, trigger the same target continuously 10 times with the same stylus, direction, and speed, take the maximum value minus the minimum value, and record it as R_same. Cross position range: Select at least three positions in the workspace (covering the edges and center, at different heights), and perform 10 repetitions each to obtain R1, R2, and R3- it is not a single number, but the degree of dispersion between these groups of numbers .There is only one interpretation logic: the difference between the two forms distinguishes between the sources of randomness and geometry. The large range at the same position indicates that there is a random source in the measurement chain (loose stylus, excessive bending of probe, loose clamping, vibration, rapid temperature change), which is independent of the position and has a form of overall amplification . The normal range at the same position but significant differences at different positions indicate that the problem is related to the position (a certain rod is compressed in this section, and a certain hinge point only exposes the gap in this posture), and the shape is local amplification * *. The range of each position is normal, but the mean value varies systematically with the position, indicating that the geometric relationship has changed and belongs to deformation.
| Data form | Typical manifestation | Main direction | Next step |
|---|---|---|---|
| Overall magnification | R at each position is large and of similar magnitude | Probe, probe, clamping, environment | Check for probe deflection (≤ 4 μ m), probe fastening, clamping and temperature |
| Partial magnification | Some positions have significantly larger R than the rest | The hinge point gap or constraint is insufficient in this posture | The measurement is intensified in this posture, and the section is rechecked with tactile feedback |
| Mean drift with position | R is normal, mean has directional trend | Geometric deformation (platform, strut, casting) | Transform to three levels, or directly enter disposal evaluation |
| Unidirectional deviation | Different deviation in two directions at the same position during reversing | Joint point backlash, insufficient unidirectional pre tension | Combined with ball joint clearance inspection |
This table breaks down ‘poor machine accuracy’ into four forms that can be traced separately. Two point caliber must be explained: The range values are all based on the historical baseline of the machine, and this article does not provide a universal threshold – the three models have different working volumes (300 is Ø 300 mm/150 mm, 500 and X-500 are Ø 500 mm/250 mm), and the same value cannot be compared on different models. The official side only has a comparison uncertainty of ± 0.002 mm at the whole machine level. 10 times is a common industry practice * *, not an official regulation, and the more times the range is, the more likely it is to be dominated by a single outlier. This should be explained in the records.
The repairability of structural damage depends on whether the damage changes the replaceable mating relationship or the non replaceable component body. What can be repaired is the coordination relationship: the clearance between the hinge points is restored by replacing the hinge parts and reassembling (requiring original factory parts and geometric review conditions); Loosening can be tightened again; Foreign objects on the installation surface can be cleaned and reattached; The stylus can be replaced. Commonality – Repairs are relative positions, and the components themselves do not deform.What cannot be repaired are the component body: casting cracks and plastic deformation, platform body deformation, strut body bending exceeding the limit, and damage to the positioning reference surface of the constraint mechanism. The commonality is that the shape or integrity has changed, while the shape is processed. Someone asked, ‘Can’t we just weld a crack?’ Welding is feasible, but it introduces thermal stress and structural changes. After welding, it must be re aged and processed, and ultimately requires geometric reconstruction and calibration, which cannot be completed on site.
Identify features.Thin lines that are unrelated to the direction of the processing pattern often have branching or sudden termination at both ends; Bubbles and discoloration along the paint surface; There are rust or oil stains seeping out from the line side (indicating that it has been connected to the inner cavity); The tapping sound is muffled in that area. Why is it irreparable.Cracks indicate that the material has separated, and relative displacement occurs on both sides of the separation surface under load, causing the geometric relationship to lose control in this direction. More importantly, cracks will propagate: under alternating loads, stress concentration occurs at the crack tip, and the length increases with cycling until the remaining section is insufficient and fractures – breaking on the base or top casting, resulting in platform drop.
On site actions.
**Discipline that must be upheld: Do not infer residual strength based on visual length, and do not write ‘this crack does not affect accuracy’. There is no corresponding relationship between crack size and strength in the baseline. Any conclusions that need to be quantified must be written as “subject to the official manual” and issued by a qualified party.
Suggestions for follow-up and disposal.There are only two practical solutions: replace the corresponding castings and reconstruct the geometry according to the complete process (which is a major overhaul and requires original factory parts and factory calibration conditions), or trade in the old for the new. Which one is more suitable depends on whether the cracked component is a base or a top casting, and the official repair plan shall prevail. In addition, for machines that have already developed cracks, other structural components may have been subjected to the same stress and should be considered as a risk.
Identify features.More difficult to detect than cracks in castings, because it is a change in geometric relationships rather than material separation. Four typical phenomena: the platform and fixture board are no longer parallel; At a certain stationary posture, there is one driving strut with a different end angle from the other two; Short or stuck travel in a certain direction; The deviation direction of spatial data varies with attitude. Why is it difficult to judge.The upper hinge point area is the throat for load transmission, and collision energy is transmitted along the strut here, which may cause plastic deformation of the installation seat, deflection of the hinge point seat, and loss of pre tension. It neither alarms nor affects kinematics, and single point repeatability may still be normal – the deviation is solidified into the “normal value of the machine”.
On site actions.
Suggestions for follow-up and disposal.If the deformation is limited to the hinge seat or fastener, and there are original parts and geometric review conditions, the hinge can be replaced, reassembled, and the geometry can be reconstructed; If the platform or strut body is deformed, it shall be classified as non repairable on site according to 3.1. Regardless of the type, the complete geometric reconstruction process must be followed after disposal: mechanical reset, leveling and anchoring, needle changing frame positioning, calibration mastering, Retest.
Identify features.All of them are data features, so they are the most difficult to recognize: the appearance passes, there are no alarms during movement, and the single point repeatability is still acceptable, but the deviation direction at different positions is not consistent, or the consistency of needle position deteriorates after needle change – the mean value drifts with position and the range is normal.
Why is it called ‘framework’.It is not a single component, but rather the set of constraint points where the geometric relationship between the three struts is established: the axis pin and bearing of the upper and lower Hooke hinges, the connection surface of the hinge seat, the positioning surface of the constraint mechanism, and the installation surface of the platform. Frame failure means that the relative positions of this set of constraint points undergo non repeatable changes, or gaps appear that only close in specific poses. Why can’t the software be replenished.The premise of compensation correction is stable deviation; The deviation of frame failure varies with position, probe direction, and load direction. The positive and negative readings at the same point are different, and compensation can only be taken as one value. whichever value is taken will make the other half worse.
On site actions.
Suggestions for follow-up and disposal.The failure of the measurement framework requires the re establishment of geometric relationships, which should be done by the original factory path or the party with equivalent measurement conditions. When evaluating, the degree of differentiation is based on the number of directions in the data: if only one direction usually points to a single point, if multiple directions appear simultaneously and change with position, it points to the entire framework. This reasoning is a common practice in the industry, and its limitations should be explained.
| Step | Action | Judgment | Branch |
|---|---|---|---|
| 1 | Power off and let it stand, confirm safe access | There is no risk of electrification, and the platform is not stuck in the limit | Cannot be confirmed → Stop, hand over to professional personnel |
| 2 | Visual inspection (cleaning, oblique lighting, two directions) | Check for fine lines, seepage, displacement marks | There are obvious cracks → Stop, turn to 3.2 for disposal |
| 3 | Conduct penetration after feasibility assessment (avoid coating and clean surface) | Check for open defect display | Yes display → Record and evaluate, do not handle on your own |
| 4 | Lightly push, lightly rotate, lightly tap | Whether there is any looseness, skewness, or abnormal tone | If there is looseness → Record the direction, do not enter the second level, transfer to evaluation |
| 5 | Power on, 10 times difference at the same location | R_same compared to historical baseline | Overall zoom in → Check probe, probe, clamp, environment |
| 6 | 10 times for each of the three positions | Local amplification or mean drift | Local amplification → This pose hinge point or constraint; Mean drift → transition to 3.3/3.4 |
| 7 | Reversing measurement and needle position consistency | Unidirectional deviation, needle position difference | Yes → Record, transfer to evaluation |
| 8 | Is the summary included in the three-level dismantling inspection? | Are the first two levels directed towards the structure? | Yes → Dismantling inspection is only qualitative; No → Do not do |
Three safety tips.1, The trial pushing and trial turning of the platform must be carried out in a power-off or emergency stop confirmation state, with a force so small that it does not cause movement – platform falling is the most serious consequence. 2, Penetrating consumables are volatile. The work area should be ventilated, gloves and goggles should be worn, and thoroughly cleaned afterwards. 3, Lightly tapping with only a soft handle, metal tapping itself may cause indentation and even induce microcrack propagation.
The most valuable information for evaluating an accident machine is’ what has this machine experienced ‘, not’ how much it cost to repair ‘. The same appearance and data performance may correspond to completely different costs. The watershed is four historical facts: no collision, no liquid intake, no overload, and incomplete attachments and calibration records.Four things have different weights: collision determines the level of suspicion in the structural layer; Entering the liquid determines whether the electrical layer has failed (the official statement states that entering the liquid must be powered off and cannot be re powered on, and should be returned to the supplier for replacement, which is not covered by warranty and RBE); Overload determines the stress history of structural components; Attachments and records determine whether the evaluation falls under the category of ‘repairable’ or ‘discounted’.
First thing: Have you ever crashed into a plane.Don’t ask ‘Have you ever collided?’ ask ‘When was the last collision, was it a workpiece or a fixture, what was the alarm code, and what actions have been taken since then.’. Details are often difficult to remember, but remember ‘what was done afterwards’ – whether it was reset, changed the stylus, or recalibrated. Simultaneously inspect the physical object: check for any breakage or bending of the probe ball head, check for any impact marks on the probe housing, and check for any impact marks on the fixture plate; When there is a discrepancy between the physical object and the oral description, the physical object shall prevail.
Second item: Has the liquid been injected.Ask about the usage environment (cutting fluid spray, nearby cleaning processes, upper pipelines) and check for traces: water stains on the bottom of the base, corrosion of the controller and cable joints, discoloration of the fan filter due to moisture, and rust spots on the electrical box. After confirming that the liquid has entered, follow the official disposal requirements and do not “dry it before turning it on” – re powering on may turn “replacement needed” into “multiple damages”.
The third item: whether it is overloaded.The official maximum workpiece weight is 25 kg for 300, 100 kg for 500 (including fixture plate), and 100 kg for X-500 (25 kg during MTS operation). The confirmation method is to calculate the total weight: the workpiece is added with fixtures and cushion blocks. The hidden source of overload is clamping force – using a pressure plate to forcefully flatten uneven workpieces, the reaction force will be transmitted to the platform and struts, so it is necessary to ask “how to press and whether there is forced flattening”.
The fourth item: attachments and calibration records.Standard parts certificate and expiration date, probe configuration list, cleaning kit and fan filter replacement records, maintenance records, and .CAL file retention are required. This is not a bonus point – * * Without certified standard parts, the prerequisite for comparison uncertainty of ± 0.002 mm does not hold, and cannot be written as’ accuracy meets standard ‘; Without historical data, the comparison in section 2.6 loses its baseline.
| Confirmation item | Impact when the conclusion is’ yes’ | When the conclusion is’ no ‘or’ unable to confirm ‘ | Input level prompt |
|---|---|---|---|
| Collision with aircraft | Suspected structural layer has increased, requiring third level or cross position measurement | First and second level measurements still need to be conducted, and cannot be ruled out based on verbal statements | When it comes to casting replacement, a considerable proportion of new aircraft can be invested |
| After entering the liquid, the electrical components are evaluated as a whole and cannot be tested on the machine. Water stains and corrosion marks still need to be checked. Electrical component replacement is usually in the range of thousands to tens of thousands of yuan | |||
| Overloading | Abnormal stress history of structural components, overlapping risks of cracks and deformations | It is still necessary to verify the actual total weight of fixtures and workpieces | Combined evaluation with collision machine, which may trigger the exchange of old for new |
| Complete attachments and records | Can be used for complete accuracy recovery and baseline comparison | Can only be used for status assessment, accuracy conclusions must be retained | If standard parts are missing, they need to be purchased, which is a foreseeable cost |
This table is not a quotation, but an evaluation depth: if all four items are confirmed and the conclusion is good, the evaluation can be stopped at level two; If any item is’ yes’, it must be classified as Level 3 or directly transferred to disposal evaluation; Multiple items are marked as’ yes’, indicating that the machine is closer to the end of trade in.
Scope of application.The three-level detection method is applicable to the parallel structure series Equator 300/500/X-500; The interpretation logic is strongly related to the structural form. If a measuring machine or machine tool with a serial structure is used, the same data form will have different interpretations.
Permission and ability should be viewed separately.The official document states that there are no user repairable components inside the controller, and component replacement is carried out by Renishaw business representatives – this restricts the user from self repairing. Third party professional maintenance can perform both board level and component level repairs (power modules, driver boards, interface boards, connectors, fans and filters, storage media, cables). The two are not contradictory, but three boundaries must be clarified: non original factory repairs will void the original factory warranty for the component; After repair, accuracy, security, and license availability must be rechecked; In cases of structural deformation, damage to the grating body, and the need for original factory calibration or encryption upgrade packages and license migration, it is still recommended to follow the original factory path. The structural component damage discussed in this article is falling on the third boundary – this is a matter of capability and risk, not a matter of authority.
Whether reporting to one’s own boss or conducting a second-hand evaluation for peers, the conclusion must be able to be reviewed by a third party. Therefore, the deliverables consist of three parts: measurement data, judgment basis, and conclusion boundary.
The measurement data requires repeatability: the record must include position, probe, velocity, approach direction, number of cycles, temperature, and time. Missing one data item can only be considered as “observation” and not “evidence”.
The judgment criteria require traceability – each “nonconformity” must point to a clear source: an official data sheet/manual, the historical baseline of the machine, or an empirical criterion labeled as “industry practice” in this article; The three cannot be mixed.
The conclusion boundary requires honest retention – which ones are determined (with cracks on the appearance), which ones are inferred (with range differences pointing to hinge point gaps), and which ones cannot be quantified on site. The credibility of a report often lies not in the conclusion itself, but in whether it is written or not.
| Project | Collection Method | Record Content | Criterion Source | Common Misclassifications |
|---|---|---|---|---|
| Appearance and cracks | After cleaning, take oblique photos in two directions and perform penetration on suspicious areas | Position, direction, presence or absence of seepage, photos | Qualitative and quantitative analysis based on official manuals | Treat processed patterns as cracks; Treat coating cracks as substrate cracks |
| Drift and deviation | Lightly push with fingertips when power is off, symmetrically push with both hands | Which direction and relative feeling when walking in the air | Texture judgment, no measurement value | Excessive force causes the overall displacement of the mechanism to be treated as slack |
| Same position range | Fixed position, same stylus and same speed, 10 times | 10 readings, range, mean, temperature | Comparison with the historical baseline of the machine | Mixing data from different measuring needles |
| Cross position range | At least 10 times for each of the 3 positions | Range and mean for each position, position coordinates | Discrepancy between ranges | Positions selected too concentrated to cover the edges |
| Reversing deviation | forward and reverse approximation at the same position | difference between readings in both directions | comparison with the historical baseline of the machine | insufficient overtravel left before reverse approximation |
| Head deflection | UCCServer Equator → Advanced → Equator Server → Coordinate Measuring Machine Controller → General → Head deflection | Reading and time | Official criterion ≤ 4 μ m | Suspect structure if exceeding limit, without ruling out the possibility of probe deflection first |
| Liquid inlet and corrosion | Visual water stains, joint corrosion, filter discoloration | Location and range | Official: Power off when entering the liquid, cannot be reconnected | Dry and test the machine |
| Load history | Inquire about added weight | Total weight of workpiece, fixture, and cushion block | Official maximum workpiece weight of 25/100/100 kg | Only counting workpieces and not fixtures |
This table can serve as the skeleton for on-site record keeping. The cells that cannot be filled out are also information – if the “historical baseline” is empty, it means that vertical comparison cannot be made and the confidence level needs to be lowered.
Grade A: The structure is intact and the accuracy can be restored.There is no problem at the first level, the range and mean of each position at the second level can be compared with the baseline, and the deviation of the probe meets the standard. The problem at this point is that ‘restoration’ is not ‘repair’, and a complete geometric reconstruction is sufficient, with investment typically ranging from thousands to tens of thousands of yuan.
Grade B: The structure is intact, but the attachments or benchmarks are missing.Passed Level 1 and Level 2, lacking standard component certificates, historical data, or probe configurations. The disposal is to redo the geometric reconstruction after completing the attachments, and the conclusion must state ‘accuracy unverified’.
Grade C: Local damage requires replacement of replaceable parts and reconstruction of geometry.Pointing to the gap between hinge points, loose fastening, foreign objects on the installation surface, and damage to the stylus and probe module, which can be repaired, but may account for a considerable proportion of the investment in new machines.
Grade D: Damage to the structural component body.The criteria are casting cracks, deformation of the platform or strut body, and failure of the measuring frame. This article discusses the choice between replacing components (major repairs) and exchanging old for new.
The boundary between the four levels must be clearly written, because the most common dispute in second-hand appraisal is selling the third level as the first level and repairing the third level as the third level. Holding onto the principle of ‘downshifting when data is insufficient’ is more responsible than giving optimistic conclusions.
Some signs may take some time to manifest: the gap between the hinge points may be pre tightened and eaten up during standing, and only appear when running hot; Microcracks in castings propagate during load cycles; The positional relationship of the framework only reveals inconsistency after repeated movement. So the evaluation conclusion should include the conditions for re evaluation: when it is necessary to re evaluate (collision again, moving machine, overload, abnormal alarm, accuracy trend decline), and the minimum content (first level visual and second level cross position measurement). The frequency is a common practice in the industry.
After an accident, a precision structural component processing factory is preparing to transfer an Equator 500. The buyer wants to determine whether the structure can still be used before payment.
On site promotion will be carried out in three levels. Level 1: After cleaning, visually inspect at an oblique angle, and there are no fine lines or seepage on the base. There is an abnormal scratch on the platform; Lightly push the platform, Y direction slightly empty, X is empty; Tap lightly on the base and top casting to achieve consistent sound. Level 2: The center and two edges are measured 10 times each, and the center range is close to the archive. The range of the two edges is significantly larger and more pronounced towards the outer edge; The reversal measurement shows that the difference between the forward and reverse directions in the Y direction is greater than in other directions; The probe deflection is normal.
Interpretation: There are no cracks on the appearance, but the enlarged edge range and the Y-direction reversal difference both point to the vicinity of the Y-direction, indicating that the problem is concentrated rather than scattered. The seller acknowledges that they hit the fixture with a stylus three months ago. The conclusion falls above level C: no evidence of structural damage was found, but there is measurable backlash at the hinge points, and replacement of hinges and reconstruction of geometric evaluation are required for investment. Both parties are expected to complete the transaction according to the third tier investment, and the buyer will take over and complete the geometric reconstruction and restoration.
The most valuable criterion for reuse in this case is directional consistency: two independent checks point in the same direction, and cross validation is more reliable than the absolute value of any single data. If the touch points to X and the data points to Y, suspect that one of them is being clamped or interfered with by the stylus.
A certain user has multiple devices of the same model, and one of them has fluctuating comparison results. It is unrealistic to conduct a complete three-level screening one by one, so a two-level screening is used: all machines are tested 10 times at the same three positions using the same program, stylus, and standard ball, and only the range and mean are recorded. Sort by range dispersion, the one with fluctuations ranks high, and the mean drift is significantly greater than that of the same batch.
This step transforms’ suspecting that machine ‘into’ that machine’s data is indeed different from the same batch ‘. After conducting a second level review of the platform, it was found that the edge near one corner of the platform was slightly raised, and the corresponding fastener markings at the end of the strut were misplaced. The conclusion is that the pre tightening of the hinge seat has been lost and needs to be disposed of according to the original factory path. The value lies in comparison with the same batch: the machine mechanism dimensions and assembly conditions of the same batch and configuration are basically the same, and the range can be directly compared. It is still affected by its service life, clamping history, and environmental differences, and is a common industry practice that cannot replace official acceptance.
It is possible to identify a portion, but it is necessary to distinguish between “exclusion” and “confirmation”. Excluded: surface cracks, obvious gaps, obvious bending and tilting, as well as geometric inconsistencies exposed by cross position measurements. What cannot be confirmed are the measurement values: straightness, flatness, hinge point clearance, crack depth. When evaluating, it is necessary to say ‘no obvious deformation was found’ instead of ‘qualified deformation’ in order for the conclusion to stand; It is worth questioning the source of the specific numerical value that appears in an evaluation without inspection.
No. Penetration relies on capillary action and only enters the open defects leading to the surface, without responding to residual stress, closed cracks, and internal shrinkage. It can answer ‘whether there are openings on the surface that are connected to the substrate’, but cannot answer ‘how much strength is left’. The display does not provide depth information, and the depth of the color trace is not proportional to the depth of the crack. It cannot evaluate the remaining life and is only suitable as a confirmation method.
No. The same position range only proves consistency under the same posture, and has low sensitivity to geometric deformation – for machines with tilted platforms, as long as they stabilize in the same position every time, the range looks very good. What is truly sensitive is the difference between different positions: the degree of dispersion of the range points to the constraint problem under that posture, and the systematic drift of the mean points to geometric deformation. Construct the structure in at least three positions, covering the edges and center.
There are two situations. In the free state, it can be clearly seen with a ruler, indicating that it has exceeded the “minor” level. It should be evaluated according to the component level damage assessment – bending will change the actual length and reduce the compressive stiffness. If there is only a slight unevenness in light transmission in a certain section, and there is no abnormal trend in the range and mean of spatial data, observation can be carried out first, but it should be clearly stated that “no obvious bending is observed, not quantified” and listed as the focus of the next re evaluation. There is no available numerical threshold here, and any ‘within how many millimeters can be bent’ must indicate the source of reference.
First look at the appearance, but don’t just focus on the appearance. Visual inspection is cheap, fast, and can immediately detect issues that require shutdown, and must be done before any power on action. However, passing the appearance cannot be used as a conclusion, and secondary measurements must be conducted. Conversely, by powering on the program and moving with undetected structural issues, a repairable state may become irreparable. The sequence is: power-off visual and tactile inspection → no suspicion before power on measurement → measurement abnormalities return to visual inspection. These three steps are loops, not straight lines.
Treat it as a same level event. The official installation and controller guide lists the needle changing frame positioning (Part 1 and Part 2) as a necessary process after moving or changing the frame, indicating that the movement itself will change the geometric reference. Machines that have been moved must undergo at least a first level displacement trace inspection (marking the relative ground of the machine body and measuring the force on the feet) and a second level cross position measurement. If there are still drops, collisions, and unstable lifting during transportation, and the suspicion of structural layer increases, it should be evaluated according to the three-level path. In second-hand transactions, ‘just moving’ does not constitute a basis for exclusion.
Yes, but only horizontal comparisons can be made for the current period, not vertical comparisons. Vertical comparison requires a historical baseline of the same machine, without which we can only look at the absolute form of the current period: whether the range of each position is of the same magnitude, whether the mean systematically drifts with position, and whether the directional deviation is concentrated in one direction. These morphological judgments do not rely on historical data and remain valid. Another approach is to compare with other machines of the same model and configuration, provided that the clamping, stylus, and environmental conditions are as consistent as possible. The record should indicate ‘no historical baseline’, and the confidence level should be lowered accordingly.
Not recommended. Firstly, cracks in castings will propagate under alternating loads, with unpredictable paths and velocities, and the risk will shift from accuracy issues to platform drops. Secondly, the deviation caused by deformation varies with the posture, and compensation can only cover a part, which will result in some workpieces being judged as qualified and some being judged as out of tolerance, and the quality records will lose credibility. Thirdly, continuing production with structural issues will accumulate load history, turning the disposal of replaceable components into a major overhaul of the entire machine. The correct approach is to stop the formal measurement use of the machine, turn it into an evaluation object, and then decide whether to repair, replace components, or trade in the old for the new based on the conclusion drawn.
The technical parameters of this article are taken from the following official documents: Equator 300 Data Sheet H-5504-8251-06-A (2026-02), Equator 300 Specification Manual H-5504-8252-04-A, Equator 500 Data Sheet H-6078-8310-01, Equator-X 500 Data Sheet H-6620-8560-01-A (2025-06), Equator Comparison Instrument User Guide H-5504-8500 (2025), Equator Controller Technical Instructions H-5504-4000-01-A, Equator Installation and Controller Guide (ID 132816/107657), Software Suite 2. x Guide (ID 134769).
The name of the structural component is quoted from the component diagram in the installation and controller guide; ± 0.002 mm is the comparison uncertainty, and three prerequisites (immediate measurement after re mastering, clamping position difference ≤ 1 mm, certified standard parts) are indispensable. The 300/500 data sheet does not have ISO 10360 chapter, only X-500 has absolute measurement indicators; The maximum workpiece weight is 25 kg for 300, 100 kg for 500 (including fixture plate), and 100 kg for X-500 (25 kg during MTS operation); The criterion for probe deflection ≤ 4 μ m is quoted from the common error table in the user guide. The three-level stratification, bipolar difference comparison method, 10 measurements, tapping and listening, same batch screening and conclusion are common practices in the industry and are not official specifications; The article does not provide limits for crack size, deformation, straightness, and flatness. The corresponding judgment shall be based on the official manual. The case data has been desensitized.
Every Equator fault eventually comes down to a specific machine type, duty cycle and batch. The criteria and procedures in this article can be used as a shop-floor checklist; when something does not add up, talk to us directly:
| Item | Detail |
|---|---|
| Company | NINGBO JCE INDUSTRIAL TECHNOLOGY CO., LTD. (JCETech) |
| Address | Room 12B17, Building 2, Zone A, Ningbo R&D Park, Juxian Subdistrict, Hi-Tech Zone, Ningbo, Zhejiang 315048, P.R. China |
| Contact | Mr. Li / Mr. Zhang |
| Phone | +86 157-5780-7400 (Mr. Li), +86 132-2194-1413 (Mr. Zhang) |
| Online booking | jcetech.cn/contact |
Repair intake and on-site service are handled at the same address. Please call before shipping a unit so transport and scheduling do not have to be repeated.
Probe, tool setter and laser interferometer repair, calibration and on-machine measurement integration.
157-5780-7400 / 132-2194-1413
打开微信扫一扫,关注「宁波匠测」
获取维修进度查询与技术支持
打开企业微信或微信扫一扫
添加专属顾问,随时沟通