Address
宁波研发园A区2栋12B17
聚贤街道,鄞州区,宁波市,浙江中国
Work Hours
周一 to 周五: 8:30AM - 10:30PM
周六 to 周日: 9:30AM - 10:30PM

A practical guide to choosing CMM stylus tip diameter: thread type first, then reach vs accuracy trade-offs, with a three-step selection process.
“Master, this hole is only 3 mm deep — what size stylus ball should I use?”
In the workshop, you hear this question almost every day. The operator holds a stylus, sizing it up against a small hole, narrow slot, or deep cavity on the drawing, then either picks one by feel and fits it, or spends ages flicking through the catalogue without deciding. Once the machine is running, the problems start: the ball is too big, the stem rubs against the workpiece edge, and trigger values wander; the ball is too small, rigidity suffers, and the stylus flexes during high-speed scanning — the data looks good, but a re-measurement won’t match. Worse still, switching to a stylus with a different ball diameter invalidates the existing calibration, and the compensation parameters in the program have to be updated too — a whole shift gone like that.
In practice, choosing the stylus tip diameter is never a simple “bigger is better” or “smaller is better” decision. It is a trade-off between two considerations. A larger tip diameter gives a bigger gap between the ball and the stylus shaft, reducing the risk of false triggers from the shaft rubbing against the workpiece, and it also averages out the effect of workpiece surface roughness for more stable measurements. A smaller tip diameter, on the other hand, is needed to reach small holes, narrow slots, and undercuts—those hard-to-access areas that nothing else can get into. The problem is that these two requirements often conflict: the feature you need to measure may be both small and deep, requiring a small tip to enter while still demanding stable, false-trigger-free measurement. In such cases, picking a stylus by feel alone will most likely end in rework.
A more subtle pitfall lies in the thread type. Many users assume that because they own a CMM from a certain brand, they should use a stylus with the corresponding thread. But when they buy it and try to screw it on, the thread does not match, or it fits only with difficulty, and the length and weight exceed the probe head’s capacity, noticeably degrading accuracy. The thread is determined by the probe head, not by the CMM brand—on the same machine, changing the probe module can change the thread from M2 to M3. If this step goes wrong, all subsequent discussion about tip diameter becomes meaningless.
This article addresses the full decision sequence that grows out of the on-site question “what size ball should I use?” We first clarify how the thread type maps to the probe, since that sets the boundary conditions for ball diameter selection. We then explain the advantages and trade-offs of large versus small balls, so you understand when to err on the larger side and when a smaller ball is unavoidable. Finally, we give a three-step selection process—first confirm reach, then optimise for accuracy—and note that changing the ball diameter affects working length and stylus weight together, so calibration and programs must be updated accordingly.
After reading this article, you will gain three things. First, a decision framework that lets you quickly narrow down the ball diameter range without leafing through thick catalogues. Second, a practical understanding of key terms such as “clearance”, “false trigger”, and “effective working length”—not just their literal definitions. Third, a stylus selection workflow you can use on the shop floor, so the next time someone asks “what size ball should I use?”, you can give a reasoned answer rather than “let’s try it and see”.
When many engineers receive a drawing and see a measured bore of Ø8, the first thing that comes to mind is a stylus tip diameter — Ø3 or Ø4? But this order is actually backwards. The stylus tip diameter is not simply whatever size you want to use; the first step is to determine what thread is fitted on the probe. The thread type is the “root” of the entire stylus — it defines the range of styli that can be screwed in, and directly sets the upper and lower limits of the stylus tip diameter.
The thread follows the probe, not the machine brand. This is worth remembering first. The brand of the CMM has no direct bearing on the stylus thread. Many domestic brands, and even some imported models, use industry-standard probe systems for their probe heads and controllers. So the correct sequence is: first identify the probe/probe head model, then determine the thread, and only then consider the stylus tip diameter and length. If you skip the first step and go straight to choosing the tip diameter, the stylus you buy may not even screw on.
How do you identify a probe? The most direct way is to check the model marking printed on the probe head or probe body, or refer to the documentation supplied with the machine. Common trigger probes such as TP2, TP20, and TP200 use M2 threads; manual probes TP1 and TP6, as well as the scanning probe SP25M, use M3 threads; the high-accuracy trigger probe TP7M uses an M4 thread; and the highest-accuracy scanning probes use M5 threads. These relationships are clearly stated in the chapter notes of the Renishaw official stylus catalogue. Note that the thread is determined by the probe model, not by the machine brand—machines from the same manufacturer can have different thread sizes depending on which probe is fitted.
Once the thread type is fixed, the ball diameter range is set. Take M2 threads as an example: in the official catalogue, the styli listed under the M2 section have a narrow ball diameter range and correspondingly thinner rod diameters. Styli with M3 threads cover a wider ball diameter range and offer more rod diameter options. M4-thread styli are officially described as “optimised for rigidity and weight, designed for high-precision probe heads and on-machine measurement on machine tools”, with larger ball diameters and thicker rods. M5 threads belong to the high-end scanning probe series, where the ball and rod combinations favour larger balls and longer rods. These limits are not arbitrary—the thread size itself constrains the maximum rod diameter, which in turn sets the minimum ball diameter: the threaded hole is only so wide, so the rod cannot be infinitely thick and the ball cannot be infinitely small. Refer to the official data sheet for the specific ball diameter ranges.
In practice, the most common mistake is assuming the thread type based on the equipment brand. For example, an engineer may assume a domestic machine uses M3 threads, only to find the probe is a TP20 module with M2 threads. Conversely, an engineer may assume an imported machine uses M2 threads, but the probe head is fitted with an SP25M scanning module using M3 threads. Both scenarios have actually occurred. So don’t guess—check the probe model.
There is a simple way to verify: if you have an old stylus on hand, just look at the diameter of the thread at the base. An M2 thread is noticeably thinner than an M3, and an M4 is thicker still. Or measure it with a thread gauge — it takes just a few seconds. Alternatively, check the machine manual, find the probe model, and cross-reference it with the official catalogue’s list of compatible probes. The Renishaw catalogue is very clear: the M2 section covers TP2, TP20, TP200, and REVO; the M3 section covers TP1, TP6, SP25M, and REVO; the M4 section covers TP7M and on-machine probing probes; the M5 section covers the highest-accuracy scanning probes. Hexagon’s brochure is also split into trigger and scanning sections, with M2, M3, M4, and M5 each having their own chapters and clear page numbers.
Another point that is easy to overlook: on systems like the Equator comparator, the thread is also determined by the installed module. Fit a TM25-20 (TP20 module) and you use M2 styli; fit an SM25-2 (SP25 scanning module) and you use M3 styli. The machine model may be identical, but different modules mean different threads. This again shows that the thread follows the probe, not the machine.
Once the thread is set, the ball diameter range is roughly defined. A stylus with M2 thread has a narrow ball diameter range and a thin stem; if the ball is too large, the stylus becomes top-heavy. M3 thread styli offer the widest choice of ball diameters and are the most flexible option. M4 thread styli have larger ball diameters and thicker stems, giving good rigidity and making them suitable for high-precision measurement. M5 thread styli are the high-end series for the highest-precision scanning probes and are used with long extension bars. These limits are not strict prohibitions—they simply reflect how the official product line is arranged. Fitting a large ball to an M2 thread is not entirely impossible, but the corresponding part number may not exist in the official catalogue; always refer to the official data sheet.
One important point to note here: the thread type only defines the ball diameter limits—it does not determine which specific ball diameter to use. The limits tell you the smallest and largest ball that can be fitted. The actual size to choose depends on the size, depth, and roughness of the feature being measured, which are covered in the following sections. But you must establish these limits first; otherwise, all subsequent calculations are pointless.
For example, an engineer needs to measure a Ø10 blind hole, 15 mm deep. Based on experience, he picks a stylus with M3 thread and a Ø3 stylus tip. When he checks the probe, it turns out to be a TP20 module with M2 thread. A Ø3 tip is available for M2 thread, but the stylus stem is only 1.5 mm in diameter and 10 mm long, so rigidity is only average. If he switches to an M2 stylus with a Ø2 tip and a 1.4 mm stem, the rigidity is actually better suited. This is the advantage of checking the thread first—it tells you what you are working with before you choose the tip.
Another example. The machine uses a scanning probe, and the engineer wants to measure a small hole with a Ø1 tip. He checks the probe model—it is an SP25M with M3 thread. A Ø1 tip is available for M3 thread, but the stem is only 0.7 mm in diameter and 21 mm long. This slender stem tends to flex in scanning mode, which affects accuracy. If the hole is slightly larger, a Ø2 or Ø3 tip with a thicker stem gives better rigidity. The thread does not change, but the choice of tip diameter directly affects rigidity and accuracy.
Finally, a practical tip: make a table listing all probe models on the machine and their corresponding threads, and keep it next to the machine or on the computer. When changing a stylus, check the table first, then the catalog, and then place the order. This table takes less than ten minutes to make, but it can save countless returns and exchanges later. The thread type is the starting point for choosing a tip—if the starting point is wrong, everything that follows is wrong.
The most immediate effect of a larger stylus tip is a bigger gap between the tip and the stem. Take an M3 threaded straight stylus (R-3-SS-1.5-L21) as an example: with a 3 mm tip and a 1.5 mm stem, the clearance between the tip edge and the stem is limited on each side. Switch to a stylus with a larger tip, and that clearance becomes much more generous. The larger the gap, the deeper the stem can reach into a step root or groove bottom without touching the wall. This depth has a dedicated field in the specification table called effective working length (EWL), measured from the centre of the tip to the point where the stem would interfere with the feature being measured. As the tip diameter increases, EWL usually increases too — in other words, a larger tip is not only “more stable” but also “reaches deeper”. When selecting a tip, look at EWL and tip diameter together: of two tips that can both enter the same hole, the one with the larger EWL is usually the one with more clearance.
Roughness is another factor that is easily underestimated. Workpiece surfaces are never perfectly smooth; machining marks, grinding lines, and even slight burrs can shift the actual contact point of the stylus tip away from its ideal position. With a small stylus tip, the contact area is small, and a tiny surface protrusion can cause the tip to bounce, introducing burr-related errors into the measured points. With a larger tip, the contact area between the sphere and the surface is greater, so the effect of any single protrusion is averaged out by the surrounding lower areas, and the measured points more closely reflect the true surface profile. Renishaw’s official selection guidelines state clearly that the stylus tip should be as large as possible, partly because a larger tip averages out the effects of workpiece surface roughness. This is not just theoretical—on workpieces with average surface quality, such as cast blanks or rough-milled surfaces, the difference in point-cloud smoothness between large and small tips is clearly visible to the naked eye.
Preventing accidental contact also relates to the dynamic stability of the stylus itself. During rapid movement and contact triggering, the stylus shaft undergoes slight bending and vibration. A stylus with a larger ball diameter and correspondingly thicker shaft usually offers more suitable rigidity, with less shaft deformation on contact and a cleaner trigger. Conversely, a slender shaft with a small ball bends slightly before triggering on contact, shifting the measured point. This difference is especially pronounced with trigger probes; although scanning probes have extremely low trigger forces, poor shaft rigidity still introduces dynamic errors. So the rule “the larger the ball, the more stable” applies to both trigger and scanning probes, though the underlying mechanism differs slightly.
The selection method is straightforward: check the drawing, confirm the minimum size of the feature to be measured to ensure the ball can enter, then choose the largest ball diameter available in the part number table. For example, M3 threaded straight styli are listed with multiple ball diameters in the catalogue, with shaft diameter increasing accordingly—refer to the official data sheet for exact values. If the bore to be measured is 8 mm and both 3 mm and 5 mm balls can enter, choose the 5 mm ball—it provides more clearance, a longer effective working length (EWL), and better resistance to surface roughness interference. Unless smaller bores are planned later, there is no need to pick a smaller ball for the sake of versatility.
One scenario deserves special mention: when measuring a plane or hole position at the bottom of a deep cavity, the stylus must extend deep into the cavity. If the stylus tip diameter is too small, the stylus shaft can easily rub against the cavity wall as it approaches, causing false triggers. A larger stylus tip keeps the shaft farther from the wall, allowing deeper penetration without contact. This is why many deep-cavity measurement tasks favor large stylus tips, even hollow ceramic balls—the large tip combined with a lightweight structure balances clearance and rigidity.
Of course, larger is not always better. As the stylus tip diameter increases, the mass at the stylus end grows, which can affect dynamic performance. Moreover, a large tip cannot enter small holes—this is the entry capability issue covered in the next section. The key principle to remember here is a priority rule: as long as the stylus can enter the feature, choose the largest tip diameter possible. This “as large as possible” is not a guess; it means comparing the ball diameter, shaft diameter, and EWL columns in the specification table and selecting the stylus with the largest clearance and longest EWL. The exact values come from the official data sheet, but the reasoning applies universally.
The stylus tip diameter determines whether the stylus can reach the feature being measured. This is not a question of accuracy but of geometric clearance — if the tip cannot enter the feature, accuracy is irrelevant.
Consider the most direct case: measuring the bottom of a 3 mm diameter blind hole. With a 3 mm stylus tip, the maximum cross-section of the tip is nearly equal to the hole diameter. In theory the tip can just enter, but the clearance between the stylus stem and the hole wall is almost zero. In practice, the hole has positional deviation, the stylus has mounting angular error, and workpiece clamping has repeatability error. Any small deviation can cause the stem to rub against the hole wall and trigger a false trigger. With a 1 mm stylus tip, there is ample clearance between the tip and the hole wall, and the stem can enter the hole bottom smoothly.
For example, measuring a counterbore 5 mm in diameter and 8 mm deep. With a 3 mm stylus tip, the tip is large and the stem is thick; the stem may contact the hole wall before reaching the bottom — at this point the effective working length (EWL) is insufficient and the measurement cannot be completed. Switching to a 1 mm stylus tip makes the stem correspondingly thinner, increasing the clearance between the tip and the hole wall. The stylus can then continue deeper until the tip centre reaches near the hole bottom. This is the geometric principle behind “a small tip can reach deeper”.
The situation with narrow slots is similar. To measure the bottom diameter of a 2 mm wide annular groove, a stylus with a 2 mm stylus tip almost fills the groove width, leaving very little clearance between the groove wall and the spherical surface—any slight tilt of the stylus will cause it to hit the wall. A stylus with a 1 mm stylus tip, by contrast, has obvious clearance inside the groove and can make stable contact with the groove bottom.
Note, however, that the advantage of a small stylus tip lies only in its ability to enter the feature. The smaller the tip diameter, the smaller the difference between the tip and the stylus stem diameter, so the tip-to-stem clearance shrinks accordingly. For example, with the M2 stepped stylus R-0.5-TC-0.32/0.7-L10, the tip diameter is 0.5 mm and the fine stem diameter is 0.32 mm—the diameter difference is very small. This means that even a slight tilt of the stylus can cause the stem to rub against the workpiece. As a result, small-tip styli demand stricter orientation control during use: the stylus axis must be kept as perpendicular to the measured surface as possible.
Another practical issue is that the smaller the tip diameter, the more sensitive the stylus is to workpiece surface roughness. A large tip averages out microscopic surface irregularities, while a small tip is more likely to pick up local peaks and valleys. Therefore, when measuring small holes on rough surfaces, the reading scatter of a small-tip stylus increases noticeably. If the hole wall is rough, it is usually necessary to increase the number of measurement points and take the average to compensate.
According to the specifications in the product catalog, each thread series offers a range of stylus tip diameters from small to large. For example, the M2 threaded straight stylus is available with a 1 mm tip and 0.7 mm shaft, as well as a 2 mm tip and 1.1 mm shaft. Smaller tip diameters, such as 0.5 mm, are found on stepped styluses, where the shaft is made in two sections: a thicker section near the mounting end for rigidity, and a thinner section near the tip for reaching into small holes. This design is intended to balance reach and accuracy.
When selecting a small stylus tip, three factors must be confirmed at the same time. First, the tip diameter must be smaller than the bore or slot width being measured, leaving sufficient clearance, which should be verified under actual working conditions. Second, the EWL must be greater than the depth being measured, otherwise the shaft will contact the wall before the tip reaches the target. Third, the shaft diameter must be thin enough to ensure that the shaft does not interfere with the bore or slot wall throughout the entire travel of the tip in contact with the measured surface. All three items are listed in the specification table in the catalog, with part number, tip diameter D, shaft diameter S, total length L, and effective working length EWL given line by line.
There is a common misconception that the smaller the stylus tip, the higher the measurement accuracy. In fact, stylus accuracy depends mainly on the sphericity grade of the tip, not its diameter. A standard Grade 5 ruby stylus tip has a sphericity deviation of 0.13 µm; for other diameters, refer to the official data sheet. The advantage of a small tip is that it can reach into tight spaces—not that it measures more accurately. If the hole is large enough, a larger tip is actually more stable: the clearance between the tip and the stylus body is greater, accidental contact is less likely, and it is less sensitive to surface roughness.
The selection logic should therefore be: first determine the minimum tip diameter that can enter the feature to be measured; then, within that constraint, choose the largest tip possible. For example, a 3 mm tip can easily enter a 6 mm diameter hole, so there is no need to choose a 1 mm tip—the larger tip offers better rigidity and more stable measurement. Only when the hole diameter is smaller than 3 mm, or when the depth is too great and the effective working length (EWL) is insufficient, should a smaller tip be considered.
A stepped stylus is worth considering when you need to reach a small ball into a deep hole. The shaft tapers noticeably near the ball end while remaining thicker near the mounting face, which preserves both access capability and overall rigidity. In the catalogue, the M2 series offers a stepped stylus with a 0.5 mm ball and a 0.32/0.7 mm shaft; the M5 series has a similar design. This type of stylus suits small-diameter holes with some depth, such as fuel injector nozzles and hydraulic spool bores.
One final note: as the ball diameter decreases, overall stylus rigidity drops, especially with longer styluses. The catalogue’s shaft material selection follows this rule: for ball diameters of 1 mm or less with small shaft diameters, tungsten carbide shafts are used to maintain rigidity; for ball diameters of 2 mm or more with lengths up to 30 mm, stainless steel shafts are the standard choice. If a small-ball stylus also needs to be very long, rigidity becomes clearly insufficient, and bending during measurement will directly affect accuracy. In such cases, switch to a different measurement strategy—for example, a disc stylus or a custom stylus—rather than simply extending the small-ball stylus. The maximum stylus length you can use depends on the actual machine configuration and the official data sheet.
Choosing a stylus tip diameter often makes engineers hesitate because two conflicting requirements pull in opposite directions: a larger tip keeps the stylus farther from the workpiece surface and reduces the risk of accidental contact, while a smaller tip can reach into narrower holes and slots. With these two demands pulling against each other, it is easy to make a decision based on gut feeling. In fact, the selection logic repeatedly emphasised in the official catalogue can be summarised into three steps. Work through them in order, and the answer will largely become clear.
Step 1: First confirm reachability — the stylus tip must be able to reach the measured feature, and the stylus body must not touch the workpiece.
This step is about geometric interference, not accuracy. Think of the stylus as a flashlight reaching into the workpiece: the light spot (the tip) must illuminate the target position, while the barrel (the stylus body) must not jam against the hole wall. The catalogue gives a dedicated parameter for this capability, called EWL (effective working length), defined as the distance from the sphere centre to the point where the stylus body would interfere with the measured feature. In other words, EWL is the depth the tip can reach before the stylus body touches the workpiece. When selecting a tip, first check the EWL for that stylus in the catalogue, then compare it with the depth and opening size of the feature to be measured. If the EWL is insufficient, a perfectly round tip or a perfectly straight stylus is of no use, because it simply cannot reach the feature.
For example, to measure the bottom of a blind hole with a diameter of 6 mm and a depth of 15 mm, take a straight stylus with M3 thread and a stylus tip diameter of 3 mm. The stylus stem diameter is 1.5 mm, leaving a gap of about 1.5 mm between the stylus tip and the hole wall. This looks acceptable, but the EWL is limited. With a hole depth of 15 mm, the stylus tip may not reach the bottom. In this case, either switch to a stylus with a longer EWL, or use a smaller stylus tip diameter to reduce the stem diameter, making the stem thinner so it can reach deeper. The check is simple: measure the hole depth first, then look up the EWL in the catalogue. Only when the EWL exceeds the hole depth can the stylus be considered to “reach”.
There is another easily overlooked dimension — the probe head itself. The stylus is screwed onto the probe head, which has its own dimensions, and the probe head body also has a diameter. If the stylus is too short, the probe head body may hit the workpiece edge before the stylus does. The official documentation for star styli specifically notes that the stylus tips must extend beyond the diameter of the probe head body to allow probing in certain directions. The same applies to straight styli: when selecting length, account for the probe head body size and leave a safe clearance. There is no universal formula for this — it depends on the actual machine configuration — but the principle is clear: first make sure the stylus assembly can reach the target area, then consider the stylus tip diameter.
Step 2: Then confirm “accuracy” — with reachability ensured, use the largest stylus tip possible.
One of the official selection principles states, in so many words: make the stylus tip as large as possible. There are two reasons for this, both directly tied to measurement quality. First, a larger tip diameter increases the clearance between the tip and the stylus stem, reducing the chance of false triggers caused by the stem contacting the workpiece surface. Second, a larger tip averages out the effects of workpiece surface roughness — the tip does not contact an ideal point but a small area. The larger the tip, the more microscopic peaks and valleys are covered in the contact zone, and the more stable the measured values become.
The selection method for this step is: after confirming in step one that the EWL is sufficient, pick out from the catalogue all stylus configurations that can reach the feature to be measured, then choose the one with the largest tip diameter. For example, when measuring the inner wall of a through-hole with a diameter of 10 mm, if both a 3 mm and a 4 mm tip stylus can reach the position, choose the 4 mm one. A stylus with a 4 mm tip usually has a thicker stem, which provides better rigidity and more stable measurements. “Accurate probing” here does not mean the tip itself is more precise; it means the larger tip diameter provides greater clearance margin and better roughness averaging, making the measurement results more reliable.
Here is a special reminder: do not sacrifice reach for the sake of accuracy. As the stylus tip diameter increases, the stylus shaft often becomes thicker, and the EWL may also shorten. If the feature being measured is at the bottom of a deep hole, a large stylus tip may not be able to reach it, making even the largest tip useless. So the order cannot be reversed—first ensure reach, then pursue accuracy. If the two conflict, reach takes priority, because a position that cannot be reached cannot be measured, and accuracy is meaningless there.
Step 3: Finally check the “linked items”—when the stylus tip diameter changes, the working length and the stylus’s own weight change accordingly.
Now for weight. The larger the stylus ball, the greater the mass at the tip. A stylus is a cantilever structure, so the heavier the tip, the more inertia it carries during motion or vibration, and the more likely it is to cause false triggers. Official documentation notes that ruby’s low density keeps tip mass low, which helps avoid false triggers caused by machine motion or vibration—this is one reason ruby is the standard stylus ball material. But as ball diameter grows beyond a certain point, tip mass still rises noticeably. For standard kinematic trigger probes, very long stylus and extension bar combinations are already discouraged, because lower rigidity and bending degrade accuracy; an oversized ball adds further load on the tip. If the feature being measured allows it, prefer a short stylus with a large ball over a long stylus with a large ball—the official selection guidelines list “use short” and “use as large a ball as possible” as two parallel rules that should be applied together.
Another linked factor that is easy to overlook is the joint between the stylus and the extension bar. Each extension bar added introduces one more joint surface, and therefore one more potential bending point and deviation point. When the stylus tip diameter increases, if the feature cannot be reached, some people habitually add an extension bar to compensate. However, this increases both the overhang and the number of joints, resulting in a double loss of accuracy. The correct approach is: first check whether a longer one-piece stylus is available in the same series, then see whether a slightly smaller stylus tip can be used in exchange for a longer EWL, and only consider an extension bar as a last resort. In the official selection guidelines, the principle of “minimise the number of joints” takes priority over “use the largest stylus tip possible” — once there are too many joints, even a larger stylus tip cannot compensate for the error caused by bending.
After completing these three steps, selecting the stylus tip diameter changes from a vague “feel” into an actionable decision process: first check the EWL to confirm reach, then choose the largest stylus tip within that reach, and finally verify the knock-on effects of the diameter change on EWL and weight. If all three steps are satisfied, the stylus is essentially a sound choice for the current application. If no ready-made part number in the catalogue meets all three requirements, the measurement strategy for the feature should be reconsidered — for example, switching to a different stylus type (disc, cylinder, or star) rather than forcing an unsuitable straight stylus into service.
Let’s first look at how EWL gets “squeezed out” by the ball diameter.
EWL is defined as the distance from the stylus tip centre to the point where the stylus shaft would interfere with the feature being measured. As the stylus tip diameter increases, with the tip centre position unchanged, the ball itself bulges outward and the clearance between the shaft and the workpiece does increase—this is the “stability” mentioned in Section 2. But the trade-off is: for a given overall stylus length, a larger tip diameter means more of that length is taken up by the tip radius, pushing the shaft start point further back. In other words, the depth the ball can “reach into” is limited by the larger ball itself.
Take a common shop-floor example: measuring a blind hole with a diameter of 8 mm and a depth of 12 mm. With a Ø3 mm tip and a 21 mm overall straight stylus, the distance from the tip centre to the shaft start, combined with the thin shaft, allows probing near the hole bottom. Switching to a Ø6 mm tip with the same overall length, the larger tip radius takes up more of that length, so the shaft start point sits further back than with the Ø3 mm tip. If there is a step or a small cross-hole at the bottom, the Ø6 mm stylus shaft may contact the hole wall prematurely, causing a false trigger. In this case, the issue is not that the tip is too small—it’s that the EWL is insufficient.
Conversely, reducing the ball diameter does lengthen the EWL, but the stylus shaft usually gets thinner too. The official specification sheet makes this clear: for example, one M3 straight stylus (R-1-SS-0.7-L21) has a 1 mm ball and a 0.7 mm shaft; another M3 straight stylus (R-3-SS-1.5-L21) has a 3 mm ball and a 1.5 mm shaft. A thinner shaft directly reduces bending stiffness. At the same length, a thin shaft deflects more than a thick one, which degrades trigger repeatability. This is the “hit accuracy” issue — a smaller ball can reach into tight spots, but whether the measured point stays stable depends on how stiff the shaft is.
Now let’s see how self-weight grows with ball diameter.
As the ball diameter increases, the sphere volume grows cubically, so the tip mass rises accordingly. Ruby has a density of about 3.9 g/cm³, so a larger ball adds noticeable weight. That weight sits at the end of the stylus, acting as a cantilever load on the probe head. Trigger probes reset via a kinematic mechanism; with a heavier tip, the inertial impact during reset is greater, which can cause false triggers. Scanning probes have very low trigger forces, but added tip mass still reduces dynamic response.
A subtler issue is that the choice of stylus material is constrained by self-weight. The manufacturer’s recommended ranges for stylus materials are clearly stated: stainless steel is suitable for stylus tips ≥ 2 mm in diameter with lengths up to 30 mm; tungsten carbide is used for small stylus diameters of 1 mm or less, or for lengths up to 50 mm; ceramic is used for stylus tips larger than 3 mm in diameter with lengths exceeding 30 mm; carbon fibre is used when the length exceeds 50 mm. These ranges are not arbitrary—they represent the balance point between self-weight and rigidity, calculated from “material density × length”.
How to judge in the field: when you pick up a stylus, first check the overall length and stylus tip diameter, then estimate the material. If the overall length exceeds 50 mm and the material is still stainless steel, the stylus is likely to be heavy, so use caution when mounting it on a scanning probe. If the stylus tip is below 1 mm in diameter, the stylus stem below 0.7 mm, and the overall length reaches 20 mm, the rigidity of this stylus relies on the tungsten carbide stem—do not expect it to perform high-speed scanning.
The actual selection sequence for the three linked factors should be:
First set the thread (following the probe), then set the upper limit of the stylus ball diameter (determined by the smallest bore to be measured), and check the corresponding stylus stem diameter and EWL for that ball size. Finally, verify that the total length meets the depth requirement. If the EWL is insufficient, the solution is not simply to switch to a larger or smaller ball, but to change the stylus form — for example, a stepped stylus. The official naming for stepped styli includes notation such as “TC-1/4”; the exact meaning follows the official naming protocol. The stepped stylus is thin near the ball and thick near the mounting face, which preserves the ability to enter small bores while restoring rigidity through the thicker section.
Another point that is easy to overlook is the extension bar. The extension bar itself has weight and length, and each additional joint adds another interface and another potential bending point. As the stylus ball diameter increases, the stylus weight increases; adding an extension bar on top may push the total tip weight beyond the probe’s allowable limit. The official recommendation is to use the shortest stylus that meets the application and to minimise the number of joints. This is not conservatism — it is the physics of a cantilever beam: the longer the overhang, the faster the tip deflection grows.
Finally, here is a practical on-site rule of thumb:
Don’t just look at the CMM brand—first confirm the model of the probe head and probe. The thread specification follows the probe, not the machine brand. Many domestic CMM brands use Renishaw-style probe heads and controllers, so “I use brand XX” doesn’t tell you the thread size. The correct approach is to check the model marked on the probe head—TP20, TP200, or SP25M, for example—and then look up the thread specification for that probe model. Renishaw’s official catalogue is clear: M2 thread is used for TP2, TP20, TP200, and REVO; M3 thread for TP1, TP6, SP25M, and REVO; M4 thread for TP7M and machine-tool probing probes; M5 thread for the highest-accuracy scanning probes. If you’re using a Hexagon probe head, refer to the Hexagon Styli and Accessories catalogue—page 34 has a cross-reference table between Renishaw and Hexagon, so you can look up the part number directly. In short: identify the probe first, then the thread, then the stylus ball diameter and length.
First check reach, then check accuracy. For a blind hole 6 mm in diameter and 15 mm deep, a 3 mm stylus ball on an M3 straight stylus (R-3-SS-1.5-L21) has a stem diameter of 1.5 mm, leaving about 1.5 mm clearance between the ball edge and the hole wall. However, the 15 mm hole depth means the stylus must extend 15 mm into the hole. If the overall length is insufficient, the stem will rub against the hole mouth or the bore wall. A 2 mm stylus ball typically has a 1.4 mm stem diameter (check the official data sheet), giving more clearance and easier entry. But a smaller ball has its drawbacks: the smaller the ball, the more sensitive it is to workpiece surface roughness, and measurement stability is slightly reduced. Recommended approach: first use a caliper or depth gauge to confirm the actual hole depth, then check the stylus EWL (effective working length) in the official data sheet — EWL is measured from the ball centre to the point where the stem would contact the wall. As long as the EWL exceeds 15 mm, a 3 mm ball is usable; if not, switch to a 2 mm ball. Remember the three official selection principles: use the shortest stylus that meets the application, minimise the number of joints, and use the largest ball possible. Provided the stylus can reach in without the stem rubbing, choose the larger ball.
First, confirm whether this is a heavy-duty scanning application. If it is typical heavy-duty scanning of aluminium parts, adhesive wear is the likely cause. Synthetic ruby is 99% pure alumina. During heavy-duty scanning of aluminium, the aluminium material is attracted to the ruby ball, and aluminium transfers onto the ball surface and builds up. As the build-up grows, the effective ball diameter increases, and the measured data drifts accordingly. Renishaw has explicitly documented this condition: for heavy-duty scanning on aluminium parts, silicon nitride styli are recommended. Silicon nitride has significantly higher fracture toughness and compressive strength than ruby; refer to the official data sheet for specific values. Note, however, that silicon nitride exhibits noticeable abrasive wear when scanning steel parts, so its use should be limited to heavy-duty scanning of aluminium. Additionally, if you are heavy-duty scanning cast iron parts, abrasive wear can occur on the ruby ball surface; the official recommendation is to switch to zirconia balls. Zirconia has a hardness of HV1200, wear resistance close to that of ruby, and a fracture toughness of 10, making it suitable for demanding cast iron scanning. When changing ball material, note that not all aluminium applications require this—only heavy-duty scanning does.
Yes, you can, but you need to understand the trade-off. The official selection guidelines list three principles, one of which is explicitly “minimize the number of joints”—each additional stylus or extension bar adds a potential bending point and a source of deviation. Extension bars are meant to improve reach, but every extra joint reduces rigidity. Whether you can use them depends on the accuracy you need and the probe type. For a standard kinematic trigger probe (such as TP20), long stylus-plus-extension combinations are not recommended, because the loss of rigidity and bending will degrade accuracy. With strain-gauge probes (such as SP25M), trigger force is extremely low, so longer combinations can be used without significant loss of accuracy. The M2 stylus kit includes extension bars of 5, 10, 20 and 30 mm; for individual extension bars, refer to the official data sheet. Recommended approach: first calculate the total overhang length, then check the rigidity data for the corresponding stylus and extension bar in the official data sheet. If the total length exceeds 50 mm, prefer a carbon-fibre stylus (Renishaw GF), because carbon fibre gives the best rigidity and very low mass at lengths above 50 mm. In short, use as few joints as possible; when joints are unavoidable, choose the shortest extension bar.
This is a typical application for disc styli. Star styli and straight styli have difficulty reaching positions such as undercuts and grooves — a disc stylus is designed for exactly this. A disc stylus is essentially a section of a high-sphericity sphere; probing with its spherical edge is equivalent to probing near the equator of a very large stylus ball. Note, however, that a plain disc stylus can only effectively probe in the X and Y directions, and calibration only requires measuring one diameter (usually in a ring gauge). If you also need to measure in Z, you must add a radius end roller, provided the roller centre extends beyond the diameter of the probe head body; calibration can then be done on a sphere or gauge block. In addition, the thin disc must be carefully angularly aligned, otherwise contact will be incorrect. Your groove width is 2 mm, so choose a disc stylus with a disc thickness less than 2 mm (official disc styli are available in various thicknesses — refer to the official data sheet). Select a disc diameter smaller than the 20 mm groove bottom diameter, for example an 18 mm disc. If there is a deep hole at the groove bottom that also needs measuring, choose a disc stylus with a central thread and mount a stylus at the centre to probe the bottom of the deep hole.
Ready-made stylus kits are available, so you don’t have to order individual styli. The Hexagon catalogue lists two trigger probe stylus kits: M2 stylus kit 1 (part number 03969075), which includes straight styli with various ball diameters and extension bars in lengths of 5/10/20/30; and M3 stylus kit 2 (part number 03969040), which includes M3 straight styli and extension bars. There is also a dedicated scanning stylus kit (part number M00-694-008-000) for the HP-S-X1C scanning probe, which includes a suction cup and a star stylus holder. Renishaw offers a similar stylus kit concept, but you need to check the official catalogue for specific part numbers. The advantage of buying a kit is that it saves you the trouble of selecting individual components, but note that the stylus combination in a kit is fixed and may not exactly match your workpiece. Recommended approach: first confirm whether your probe thread is M2 or M3, then check the official data sheet to see whether the ball diameters and lengths in the kit cover your common measurement tasks. If the ball diameters in the kit are too large or too small, order one or two additional styli separately. Also, the extension bars in the kit are threaded, so the same principle of minimising joints applies—use a short bar whenever a long one is not necessary.
Looking at “reach” and “accuracy” together, the real challenge in selecting a stylus tip diameter is not the instrument itself, but thinking it through before acting. A CMM is not a cure-all—every reading it produces depends on the stylus making stable contact with the sphere. So there is only one rule to apply: first confirm the stylus can make stable contact with the surface being measured, then talk about accuracy; if the contact is unreliable, any number after the decimal point is just self-reassurance.
In practice, just follow three steps. First, confirm the thread type matches the probe, then confirm the stylus tip can reach the measured position and the stylus body does not touch the workpiece—this step checks whether the EWL is greater than the measured depth. Second, with reach confirmed, choose the stylus with the largest tip diameter—a larger tip gives more clearance, fewer false triggers, and averages out the effect of surface roughness. Third, check the knock-on effects of the larger tip diameter: is the EWL still sufficient, is the stylus body thick enough, and is the tip weight within the probe’s allowable range? If all three steps pass, that stylus is a sound choice for the current application.
The beauty of this principle is that it requires no complex formulas—just one habit: before choosing a stylus, ask yourself, “Will this stylus reach? And once it reaches, will it stand steady?” If the answer is not clear, check the official data sheet until it is. Tomorrow, pick any workpiece in the workshop and try it on a CMM. You will find that what really affects the result is often not machine accuracy, but whether the stylus you chose can both reach and measure accurately. Remember, stylus tip diameter is not about getting a better reading—it is about making the stylus stand steady first.
Every machine tool has different configuration, operating conditions, and budget. This article provides only a reference framework. You can:
NINGBO JCE INDUSTRIAL TECHNOLOGY CO., LTD. — 15 years focused on precision measurement, providing selection, installation, calibration, repair, and maintenance services for the full range of Renishaw, Marposs, and Blum-Novotest probes and tool setters.
| Contact Information | Details |
|---|---|
| Official reservation | jcetech.cn/contact |
| Consultation Hotline | 157-5780-7400 / 132-2194-1413 |
| Shipping and repair address | Ningbo Yinzhou R&D Park A2-12B17 |
| Scope of Services | Nationwide door-to-door urgent repair with 48 hour response time |
Send us the problem and let a professional engineer help you work out the numbers.
If the criteria or procedures in this article do not match your machine, send us the control system, probe model and a photo of the installation — we will answer with the specific settings rather than a generic recommendation.
| Item | Detail |
|---|---|
| Company | NINGBO JCE INDUSTRIAL TECHNOLOGY CO., LTD. (JCETech) |
| Address | Room 14-1-17, Building 033, Building 2, No. 15, Lane 587 Juxian Road, Juxian Subdistrict, Hi-Tech Zone, Ningbo 315048, Zhejiang, P.R. China |
| Contact | Mr. Li / Mr. Zhang |
| Phone | +86 157-5780-7400 (Mr. Li), +86 132-2194-1413 (Mr. Zhang) |
| Online booking | jcetech.cn/contact |
Repair intake and on-site service use the same address. Please call before shipping a unit so transport and scheduling do not have to be repeated.
Probe, tool setter and laser interferometer repair, calibration and on-machine measurement integration.
157-5780-7400 / 132-2194-1413
打开微信扫一扫,关注「宁波匠测」
获取维修进度查询与技术支持
打开企业微信或微信扫一扫
添加专属顾问,随时沟通