Address
宁波研发园A区2栋12B17
聚贤街道,鄞州区,宁波市,浙江中国
Work Hours
周一 to 周五: 8:30AM - 10:30PM
周六 to 周日: 9:30AM - 10:30PM

M2-to-M3 and M3-to-M4 thread adapters can physically fit, but they add a joint, overhang, and calibration risk. This article explains when adapting is an acceptable compromise, what it costs in stability, and what checks you must run to confirm the system remains usable.
“My probe is M2, and I only have an M3 stylus. Can’t I just add an adaptor?”
You hear this in the workshop almost every month. The person saying it has usually already screwed on the adaptor and calibrated the probe, and everything looks fine — until one day they re-measure the same part and the values drift by a few tenths, and they can’t find the cause no matter what they try.
The problem is not that the adaptor doesn’t work. It does work — the threads match, it tightens up, and the probe still triggers. The real issue is that once you add the adaptor, the stylus system in your hand is no longer the same system. It has an extra joint, more overhang, another point that can work loose, and a new set of calibration relationships that have to be re-established. None of this alarms you the moment you screw it on; it shows up later, in a subsequent measurement, as “unstable data.”
What this article does is turn “adapting” from a casual “should be fine” into a set of concrete conditions you can judge, weigh, and accept. You’ll see where common combinations like M2-to-M3 and M3-to-M4 come up, why sometimes adapting is an acceptable compromise, why sometimes you must stop and change the stylus rather than the adaptor, and what calibration and acceptance checks you need to run after adapting to confirm the system is still usable.
After reading this, you should be able to answer three questions: First, in my current situation, do I actually need an adaptor? Second, if I do use one, where exactly does the extra cost fall? Third, after converting, how do I prove nothing has gone wrong? Once these three questions are answered clearly, “whether conversion is possible” is no longer a matter of guesswork based on experience, but a decision process that can be written into a work instruction.
Before we start, here is a decision sequence that runs through the whole article: identify the probe first, then determine the thread — do not follow the CMM brand. Knowing which CMM manufacturer you use does not directly tell you the thread specification. You must first identify the probe or probe head model, then determine the thread from that model, and only then consider stylus ball diameter and length. This sequence is especially important in adaptor discussions — many cases where “an adaptor is needed” actually go wrong at the first step: someone infers the thread from the CMM brand, gets it wrong, and then uses an adaptor to compensate. The resulting system carries that cost from the very start.
Adaptors appear far more often than you might expect in CMM and on-machine measurement applications. The reason is simple: the thread on the stylus you have on hand does not match the thread on the probe head or probe. An M2 probe head cannot take an M3 stylus, and an M3 probe cannot be screwed into an M4 extension bar. So adaptors — thread adaptors, reducer sleeves, and adaptor mounts — become the temporary “fit it first, sort it out later” solution.
To decide whether an adapter is worth using, you first need to understand what problem it actually solves. It does not solve a measurement capability issue, but rather an interface mismatch problem. In other words, the adapter makes it physically possible to mount the stylus, but it adds no measurement accuracy and does not extend the measurable range.
Thread size is determined by the probe model, not by the CMM brand
This is the first rule for judging interface compatibility. Many domestic CMM brands, as well as some Mitutoyo models, use the Renishaw system for the probe head and controller. Conversely, Hexagon probes are also fitted to other CMMs. So the statement “this is a certain brand” does not tell you the thread size. The correct sequence is:
For example, if a machine is fitted with a TP20 module, the official catalogue specifies M2 thread styli. If the same machine is changed to an SP25M scanning module, the catalogue specifies M3 thread. The Equator comparator is similar — with a TM25-20 (TP20 module) it uses M2 styli, and with an SM25-2 (SP25 scanning module) it uses M3 styli. The machine did not change, but the module did, so the thread changed. If you only have M2 styli in stock, the adapter becomes necessary.
The three gaps an adapter actually fills
From an engineering standpoint, an adapter fills three types of gaps in real use:
| Gap type | Typical situation | Function of the adaptor |
|---|---|---|
| Inventory gap | Only M2 styli on site, but the probe head is M3 | Keeps existing styli usable |
| Procurement gap | The ball diameter/length needed for an urgent job is only available in another thread system | Bypasses the ordering lead time and allows measurement to start now |
| Configuration gap | Switching between different probe modules on the same machine | One stylus kit covers multiple interfaces |
These three types of gaps share one thing in common: time is short, parts are incomplete, and data is needed first. The value of an adaptor is that it turns “waiting for parts” into “measuring now”. This is especially true in emergency repairs, spot inspections, and first-article verification of outsourced parts.
What adaptors cannot solve
It is equally important to understand what they cannot solve.
First, an adaptor cannot replace proper stylus selection. The selection principle repeatedly stressed by the manufacturer is: use the shortest stylus that meets the application, and minimise the number of joints — every connection between stylus and extension bar adds a potential bending point. An adaptor is essentially one more joint; it does not change this principle, but it does make “shortest” and “fewer joints” harder to achieve.
Secondly, it cannot fill in missing specifications out of thin air. M4 is a “rare but specialized” option in both catalogues: Renishaw’s M4 section explicitly states that it is intended for the TP7M high-accuracy probe and on-machine measurement; the Hexagon catalogue devotes only one page to M4 threaded styli and accessories. If the M4 specification required on site has no corresponding part number, adapting an M3 stylus will physically fit, but the rod diameter and stiffness characteristics are those of the M3 — this must be clearly understood. Refer to the official data sheet for specific parameters.
Thirdly, it does not solve the calibration issue. After adaptation, the actual stylus length and effective working length (EWL) both change — EWL is measured from the stylus tip centre to the point where the stylus stem would interfere with the feature being measured, while total length L is measured from the mounting face to the tip centre. Adding an adaptor increases the distance from the mounting face to the tip centre, so the existing calibration data is no longer valid and recalibration is required. This is covered in Section 6.
A practical way to decide: first ask “Can I change the stylus?”, then ask “Do I need an adaptor?”
Here is a decision sequence that equipment engineers can follow:
The purpose of this sequence is to downgrade the adapter from a “default option” to a “last resort”. Adapters should be available in the warehouse, but they should not be written into the process documentation by default.
Position of adapters in the catalogue
The role of adapters is also evident from the layout of the two catalogues. In the Hexagon catalogue, “Suction cup and adapter” appears as an accessory under the stylus section (see page 44 for the scanning M3 section and page 61 for the M5 section), alongside styli, extension bars, and stylus kits, but listed after styli. This order itself shows that the stylus is the main component, and the adapter is the accessory. Renishaw’s selection principle repeatedly emphasises “minimise the number of joints”, which conveys the same idea.
It should be noted that this article does not cover specific part numbers or specifications for adapters — these have not been verified within the factual scope of this article. For actual selection, please refer to the official data sheets. What this article aims to clarify is that adapters solve the “can it be mounted” problem caused by interface mismatch. They do not solve accuracy, stiffness, or calibration — which are precisely what measurement engineers are responsible for. The following sections will break down, one by one, the costs behind “being able to mount it”.
Adapting is not just “screw it on and you’re done”. Every additional adaptor adds four things to the stylus system that need to be re-evaluated: one mating surface, one extra overhang, one potential loosening point, and one calibration that must be redone. These four are independent of each other, but they can combine to cause problems in a single measurement, so they need to be considered separately.
Mating surface: one more surface, one more source of deformation
The threaded connection between the stylus and the probe head (or extension bar) is itself a metal-to-metal mating surface. An adaptor turns this one surface into two: one on the probe head side and one on the stylus side. Each mating surface has a slight seating error when tightened and undergoes slight elastic deformation under load. These deformations have limited effect in single-point trigger measurement, but they are amplified in scanning, deep-hole, and long-overhang applications.
How to check: fit the stylus with the adaptor, push the stylus tip gently by hand, and see whether the stylus shaft shows any visible deflection. If it does, the mating surfaces are not seating properly—clean the threads, retighten, or simply change the adaptor arrangement. Inadequate cleaning is the most common problem on the shop floor: residual oil, swarf, or adhesive left from the last assembly in the threads can cause a “false seat”, where the joint looks tight but actually shifts under load.
Overhang: length is counted along the whole chain, not per individual stylus
Engineers typically look at EWL (effective working length) when selecting a stylus, but EWL is measured from the stylus tip centre to the point where the stylus stem would interfere with the feature being measured. It does not represent the rigid length of the entire stylus chain. The adaptor itself has length, so after adding it, the distance from the probe head mounting face to the stylus tip centre increases; this added distance is the overhang. The longer the overhang, the greater the stem deflection under the same trigger force, and the more the repeatability of the trigger point is affected.
The official selection principle repeatedly stresses: use the shortest stylus that meets the application and minimise the number of joints. The direct implication is—avoid adaptors wherever possible, and use a short stylus rather than a long one. Adaptors are often added “to reach”, but the cost is a reduction in the rigidity of the entire chain.
How to judge: record the total length L with and without the adaptor (total length L is measured from the mounting face to the stylus tip centre), and compare the extra length added. If the added length is close to or exceeds the L of the original stylus, seriously consider switching to a stylus with a native threaded long shank instead of relying on an adaptor.
Loose point: vibration, temperature changes, and repeated mounting/dismounting can all cause it
Threaded connections are reliable under static conditions, but not necessarily in dynamic environments. Equipment vibration, workshop temperature variations, and repeated assembly and disassembly can all alter thread preload. One adaptor means two threaded pairs, each a potential loosening point. If one loosens, the actual stylus position shifts—and this change rarely triggers an immediate alarm. Instead, it shows up in later data as “degraded repeatability.”
Field experience shows that for styli fitted with adaptors, every assembly/disassembly cycle should be logged. Each cycle changes the thread seating condition. Workstations with frequent changes—such as inspection stations that switch models often—need particular attention. Here, adaptors are consumables, not fit-and-forget components.
How to check: periodically run a repeatability test using a standard sphere or ring gauge, and watch whether the scatter of repeated triggers from the same stylus grows. If it does, check the threads first, then inspect the stylus tip for damage, and only suspect the probe itself as a last resort.
Calibration: must be redone after any adaptor change—no exceptions.
This is the most easily overlooked and the most likely to cause trouble. Probe calibration is performed with a specific stylus configuration, and the calibrated equivalent stylus tip diameter and probe compensation values all correspond to “this stylus, this overhang length, and this joint condition.” Once an adaptor is added, even if the stylus tip diameter and stylus model remain unchanged, the mechanical behaviour of the whole chain changes and the calibration result is no longer valid.
The correct procedure is to re-calibrate the probe after the adaptor has been fitted, tightened and cleaned, and only then start measuring. Do not carry over the calibration parameters from before the adaptor was fitted, and do not “measure a few parts first and see” — any deviation you see is already mixed in with part error and calibration error, and cannot be separated.
Adaptors appear in specific forms on the shop floor. The following describes each thread combination, giving the trigger reason and the specific cost for each.
M2 is the main thread for trigger probes; the official catalogue lists it as suitable for TP2, TP20, TP200 and REVO™. M3 covers the TP1 and TP6 manual probes as well as the SP25M and REVO™ scanning probes. In the Hexagon catalogue, the M2 section covers pages 14–21 and the M3 section pages 26–30, with no shared pages in between — these are two parallel specifications, not two sizes of the same system.
There are three scenarios requiring conversion from M2 to M3. The first is stylus kit reuse: early machines were fully equipped with M2 stylus kits (e.g., M2 stylus kit Kit 1, part no. 03969075, containing various straight styli with different ball diameters and extension bars). When new stations use M3 probes, an adaptor is added to reuse the existing stylus kit, but the measurement chain changes from direct screw-in to a three-stage “probe–adaptor–stylus” configuration. The second is availability of special stylus geometries: disc, star, and other shapes may only be available as standard part numbers under one thread size. For example, the M2-Disc Stylus (R-6-SS-L10) (Hexagon 03969241 / Renishaw A-5000-3611) and the M2-Star Stylus 5-way (R-2-SS-1.4-SP20/30) (Hexagon 03969056 / Renishaw A-5000-3626) are both M2 thread. The way to check is to look up the corresponding thread section in the official catalogue to see whether the same geometry is available; if yes, order it directly in the required thread, and only consider an adaptor if not. The third is temporary contingency: if a stylus is damaged or spare parts are in transit, an adaptor can be used as a stopgap, and this must be documented in the temporary process sheet; once the spare parts arrive, restore the original configuration.
From the dimensional relationship: M2-Stylus (R-1-SS-0.7-L10) (03969201) has a 0.7 mm rod diameter and 10 mm total length; M3-Stylus (R-1-SS-0.7-L21) (03969301) has the same 0.7 mm rod diameter but a 21 mm total length. After adding the adaptor, the overhang increases while the rod diameter stays the same. The official selection rule is to use the shortest stylus that meets the application and minimise the number of joints. Each connection adds a potential bending point, and the adaptor itself is an extra joint surface.
M4 is “few but specialised” in both systems: the Renishaw catalogue describes it as “specially designed for the high-precision TP7M and on-machine probing series, optimised for rigidity and weight”; the Hexagon catalogue devotes only one page (p. 32) to M4, with stylus, extension bar and accessories all listed on that single page. A checkable part number is M4-Stylus (R-6-CE-4.5-L50) (Hexagon 03969426 / Renishaw A-5000-3709), with a ceramic rod of Ø4.5 mm and 50 mm total length.
A typical M3-to-M4 conversion scenario is when a machine tool’s on-machine probing system shares a stylus kit with a CMM: the machining centre uses a TP7M for on-machine inspection, while the CMM uses an SP25M for scanning. Since the range of M4 styli is limited, the more common approach is the reverse—adapting an M3 stylus to an M4 probe head to extend the available ball diameter and length options. The trade-offs here deserve more caution than with M2-to-M3 conversions: M4 styli are designed for a balance between stiffness and weight (“optimised for stiffness and weight”), and adding an adaptor changes the overall centre of gravity and overhang of the assembly. This affects trigger consistency on touch-trigger probes and dynamic response on scanning probes. The exact impact depends on the actual machine configuration and calibration results, but the direction is clear—after conversion, recalibration is mandatory; the original parameters cannot be carried over.
Material matching also needs attention: the M4-Stylus (R-6-CE-4.5-L50) uses a ceramic stem (CE), while the M3-Stylus (R-3-SS-1.5-L21) (03969303) uses a stainless steel stem (SS). Their thermal expansion coefficients differ, so in workshops with significant temperature fluctuations, the thermal stability of the adapted assembly must be assessed separately. During acceptance, the temperature conditions should be clearly specified.
Work through the decision sequence before you start: first identify the probe/probe head model → then determine the thread → then determine the ball diameter and length. Identify the probe first, then the thread — don’t follow the machine brand. Many domestic CMMs and some other brands use the same probe system for their probe heads and controllers. Find the probe model on the nameplate or in the equipment file, and check it against the official catalogue’s scope of application (M2 corresponds to TP2/TP20/TP200/REVO™, M3 to TP1/TP6/SP25M/REVO™, M4 to TP7M and the machine-tool probing series). Once the thread is confirmed, go to the corresponding section of the catalogue to select the stylus. If the probe model is not listed in the manual, rely on the actual equipment configuration — do not infer from experience.
| Adaptor combination | Common reason for use | Main trade-off | Handling suggestion |
|---|---|---|---|
| M2 → M3 | Reuse the M2 stylus kit; some special geometries are only available in M2 part numbers | Increased overhang and an extra bending point | Check the M3 section first for an equivalent geometry |
| M3 → M4 | M4 offers a narrow selection; you want to keep using M3 styli | Rigidity and weight balance are compromised | Recalibrate after adapting |
The common point between the two types of adaptors is that both add an extra joint face, increase overhang, introduce a potential loosening point, and require recalibration. The difference lies in the nature of the cost — M2-to-M3 mainly affects rigidity and overhang, while M3-to-M4 also affects weight distribution and material matching. These costs are not unacceptable, but they must be weighed against the specific application; the next section gives the criteria for what is acceptable and what is not.
An adaptor is not a question of “good” or “bad” — it is a question of whether the cost is worth paying. What really matters on the shop floor is whether the accuracy budget, cycle time and workpiece accessibility of the measurement can tolerate the extra joint face, the extra overhang and the extra loosening point. If they can, the adaptor is a reasonable engineering compromise; if they cannot, the correct approach is to reselect the probe or probe head, not to force a fit at the stylus end.
The tolerance band is wider than the incremental error introduced by the adaptor. This is the strictest criterion. After adding the adaptor, the deflection of the stylus system increases in the direction of the applied force, and repeatability generally degrades. The exact increment depends on the actual calibration results. The procedure is to run a comparison measurement before and after adding the adaptor, quantify the difference, and then compare it with the tolerance band on the drawing. If the difference accounts for only a small portion of the tolerance band (the specific ratio is subject to your company’s quality system requirements), the adaptor is acceptable for this operation. Conversely, for mating surfaces, datum surfaces, and geometric features that feed into subsequent calculations, the tolerance band is already tight, and the adaptor increment may consume most of the margin, so adding an adaptor is usually not recommended. For example, on a line that measures both raw stock allowance and finished surfaces: using an adaptor stylus for the raw stock is fine, but for the finished surface, switch back to the original threaded stylus whenever possible.
Only a temporary solution to reach the feature. When internal cavities, deep holes, or sides blocked by fixtures cannot be reached with an off-the-shelf native stylus, adding a temporary adaptor or extending the stylus is a typical “measure first” approach. The deciding question is: will this configuration be written into the formal measurement program and reused long term? For sampling, rework, or one-off incoming inspection, an adaptor is acceptable. For production programs, multi-shift use, or SPC data chains, the setup should be re-selected as a permanent configuration.
The probe/probe head has a fixed thread, and the workstation only has a different stylus size in stock.The probe head is an M2 system (e.g., fitted with TP2, TP20, or TP200 trigger probes), but the stock is M3 styli. Using an adaptor to make use of the existing styli and avoid stopping the line while waiting for parts is a reasonable emergency measure. However, it must be understood that the thread follows the probe/probe head, not the machine brand. The correct sequence is always: identify the probe/probe head model first, then determine the thread, then the stylus ball diameter and length. The adaptor is only a compromise made once the thread is fixed; it cannot bypass the selection process. If in doubt, check the probe nameplate or the machine documentation.
Trigger force is low, the stylus is short, and the measured surface has a single normal direction.The added play and deflection from the adaptor have a relatively manageable effect when the force is low, the overhang is short, and the stylus triggers in only one direction—for example, measuring a plane height or a single-point outer diameter. In contrast, when measuring deep holes, scanning surfaces, or triggering in multiple directions (e.g., with a star stylus with several branches), the adaptor joint is repeatedly loaded, causing unstable errors, and should generally be avoided.
After adaptation, the probe still meets the trigger and retract requirements.Trigger probes have trigger threshold and retract travel requirements, and both total length and weight change after adaptation. Acceptance criterion: after adaptation, perform a probe calibration (e.g., master ball calibration) per the equipment requirements, and check whether the ball diameter and form deviation are within the equipment’s allowable range. If within range, continue use; if out of range, shorten or lighten the assembly, or revert to the original configuration. Scanning probes are more sensitive to rigidity and weight, so adaptation requires extra caution. In the Hexagon catalogue, the scanning M3 section specifically lists “suction cups and adaptors” (page 44), confirming that this type of connection is recognised in the scanning system, but the exact configuration must follow the official data sheet.
Actual calibration and acceptance must be possible.After adaptation, the probe must be recalibrated, comparison data retained, and the record must clearly state that “this configuration is an adapted setup.” If there is no master ball, comparison artefact, or record template on site, the adaptor should not be used—when a problem occurs, it is impossible to determine whether the fault lies with the stylus, adaptor, or probe. If traceability is maintained, adaptation is a controlled compromise; without traceability, adaptation is a hidden hazard.
| Situation | Acceptable | Usually avoid |
|---|---|---|
| Tolerance zone | Loose; adaptor contribution is a small fraction | Tight; mating/reference surfaces |
| Application | Temporary work, first-off samples, rework | Production programs, SPC data chain |
| Thread | Probe thread is fixed; use existing stylus stock as a stopgap | Can reselect from the probe end |
| Loading | Light, short, single-direction | Multi-direction, deep holes, scanning |
| Calibration | Can perform comparison and keep records | No master part, no record-keeping conditions |
On-site example: a workstation uses an M2 probe head, and the tool crib has a batch of M3 Ø3 ruby styli (described as M3-Stylus (R-3-SS-1.5-L21); refer to the official data sheet for the exact part number). The workpiece has a Ø3 hole to measure, the tolerance band is wide, and the operation is incoming inspection with no SPC involvement. Fitting the M3 stylus to the M2 probe head with an adaptor, then calibrating once and keeping a comparison record, is reasonable. At the same workstation, if a machined mating surface is to be measured next week with a tighter tolerance, the stylus should be reselected from the M2 system (e.g. M2-Stylus (R-3-SS-1.5-L10), part number 03969203 / A-5000-3604) rather than continuing with the adaptor.
Adaptors are acceptable, but usually only when three conditions are met at the same time: the added error stays within the tolerance budget, the configuration is temporary or low-risk, and calibration and documentation can be carried out properly. If any one of the three is missing, go back to the probe/probe head end and reselect. An adaptor is a way to improve access, not a substitute for correct selection.
The decision is not based on feel; look at three things: the probe type, the tolerance zone of the feature being measured, and how long the stylus kit has been in service on the shop floor. If any of the following categories applies, do not use an adaptor.
1. Scanning probes for high-accuracy contouring: no adaptors. A scanning probe keeps the stylus tip in continuous contact with the workpiece, and the force direction changes constantly, so every joint becomes a bending point. Renishaw’s H-1000-3200 repeatedly stresses: use the shortest stylus that meets the application and minimise the number of joints — every connection adds a potential bending point. In the official brochure, M5 is described as “specifically designed for highest accuracy scanning probes”, while M3 explicitly covers SP25M and REVO™. Adding an adaptor to fit an M2 stylus adds a joint exactly where it should not be added. The correct approach is to select the thread according to the probe/probe head model, then choose the length and ball diameter within that thread series.
2、 When the tolerance band is as narrow as the uncertainty introduced by the adaptor, do not use an adaptor. Adding an adaptor changes both the EWL and the total length L: EWL is measured from the stylus tip centre to the point where the stylus would interfere with the feature being measured, and L is measured from the mounting face to the stylus tip centre. Adding an adaptor moves the mounting face back, so L increases, EWL changes accordingly, and the deflection curve shifts. To decide, estimate the uncertainty introduced by the adaptor and compare it with the tolerance band; if they are of the same order, the adaptor cannot be used. There is no standard formula for this estimate—typically, repeat measurements are taken on the same artefact with and without the adaptor to see how the spread changes, or the calibration results under the actual machine configuration are used as the reference. The narrower the tolerance band, the more you should use the native thread.
3. In confined spaces such as deep holes, narrow slots, and internal cavities, do not use adaptors. An adaptor adds both length and diameter. The outer diameter of an M2-to-M3 adaptor is usually larger than that of an M2 stylus, so a narrow slot that previously allowed entry may no longer be accessible, and a stylus that previously cleared the hole wall may now rub against it. Perform interference checking based on the actual assembly after the adaptor is fitted: draw the adaptor, extension bar, and stylus in assembly order, and check whether they contact the workpiece along the measurement path. Recalculate the EWL. Where the EWL is critical for entering deep holes, it is better to switch to a longer native stylus. Extension bars are matched by thread series: M2 extension bars are shown on page 19, and M3 extension bars on page 28. Refer to the official data sheet for final specifications.
4. Stylus kits that will be repeatedly assembled and disassembled on site — do not use adaptors. Every extra joint introduced by an adaptor is a potential source of looseness. In the lab, where the stylus is fitted, calibrated, used and then removed in a single session, the risk is manageable. On the shop floor, where stylus, extension bar and star stylus are changed daily, every assembly cycle puts the repeat positioning of the joint to the test. The deciding factor is frequency of assembly: if the stylus is changed several times a day or handled by different shifts, the risk of loosening accumulates with each cycle. In this case, use a stylus kit with native threads. Both M2 and M3 kits are available in the catalogue (Kit 1, part number 03969075; Kit 2, part number 03969040), covering the common stylus ball diameters and lengths in one set.
5. Applications involving metrological traceability and third-party acceptance — do not use adaptors. After an adaptor is fitted, the calibration is valid only for that particular assembly. If the adaptor is changed or the stylus is removed and refitted, the calibration must be repeated. When issuing measurement reports, establishing traceability, or undergoing third-party audits, every additional joint is a point that must be explained. Wherever possible, use native threads and document the stylus configuration in the work instruction. If an adaptor is unavoidable, manage it as part of the stylus kit and calibrate, accept and record the assembly as a single unit.
| Situation | Use adaptor? | Reason |
|---|---|---|
| Scanning probe for high-accuracy contour measurement | No | The joint face is the bending point; the official selection principle requires the fewest joints |
| Tolerance zone and adaptor uncertainty of the same order | No | The uncertainty introduced by the adaptor consumes the tolerance zone |
| Deep holes, narrow slots, internal cavities | No | The adaptor geometry may cause interference; EWL must be recalculated |
| Frequent on-site assembly/disassembly | No | Loosening accumulates with each assembly/disassembly cycle |
| Metrological traceability and third-party acceptance | No | Additional joint faces add to the explanation and documentation burden |
| Temporary emergency, wide tolerance, one-off measurement | Yes | Cost is acceptable; follow the criteria in Section 4 |
Determine the scenario A workshop CMM is fitted with a TP20 trigger probe; per the official catalogue, this is an M2-series system. To measure a deep hole, the existing M2 length options are insufficient, and someone suggests converting from M2 to M3 and then adding a longer stylus. The decision criterion: the deep-hole case applies (third criterion), and the length issue is solved by extension (both EWL and L must be recalculated after the conversion). The correct approach is to first check whether the M2 extension bar (catalogue page 19) offers a suitable length, or whether the M2 stylus kit includes a longer straight stylus; only if neither is available should you consider changing the probe/probe head configuration. The thread size is determined by the probe model — TP20 is M2, so the solution should stay within the M2 system.
When deciding whether to use an adaptor, ask these questions in order: What probe series is it? How wide is the tolerance? Does the space allow it? How often will it be assembled and disassembled? Is a report required? If any one of the five answers points to “no conversion”, do not convert. Adapting is a compromise, and whether the cost is acceptable is decided by these five questions.
Fitting the adaptor only completes the mechanical connection. What really determines whether this configuration is usable is the calibration and acceptance that follow. The extra joint faces, additional overhang and extra potential slack introduced by the adaptor will all show up in the calibration data; simply copying the native-thread procedure may mistake the errors introduced by the adaptor for errors in the machine itself, or the other way round. This section covers: which extra calibration steps are needed after conversion, which values to check at acceptance, when to pass the configuration, and when to reject it.
Fix the setup before calibration. The adapter and stylus are joined by a threaded connection, so repeatability depends on tightening torque and the condition of the contact surfaces. Three steps are required before assembly: clean, tighten, and record. Cleaning means wiping oil, chips, and fingerprints from the threaded end face and the stylus mounting face—any contamination will prevent the surfaces from seating properly. Tighten to the torque specified by the equipment or adapter supplier, following the official data sheet rather than feel. Recording means logging the assembly combination in the register: adapter model, stylus description (copied from the catalogue, e.g. M2-Stylus (R-1-SS-0.7-L10)), assembly date, and operator. If measurement data fluctuates, check this record first.
Calibration requires three additional steps. First, repeat assembly calibration: remove the stylus, reinstall it, and calibrate again. Check the repeatability of the stylus tip diameter and the probe head centre coordinates to directly verify whether there are any loose points on the mating faces. If the difference in stylus tip diameter between the two calibrations exceeds the equipment’s allowable repeatability range, follow the actual equipment configuration: check the assembly first, then the adaptor itself. Second, multi-direction trigger calibration: the extra overhang from the adaptor makes stylus rigidity inconsistent in different directions. During calibration, trigger in multiple directions and check consistency across directions; the longer the adaptor and the more mating faces, the more obvious the directional variation. Third, overall calibration of the extension bar assembly: if an extension bar is fitted behind the adaptor, do not calibrate the stylus alone—calibrate the entire assembly as one unit. In the catalogue, each stylus lists two fields: EWL (effective working length) and L (total length). EWL is measured from the stylus tip centre to the point where the stylus stem would interfere with the feature being measured; L is measured from the mounting face to the tip centre. After adding the adaptor, the usable EWL becomes shorter than the single stylus’ nominal value, so calibration and programming must be based on the actual assembly.
Acceptance is mainly judged by four quantities. Repeatability of stylus tip diameter: check the difference in diameter across multiple calibration runs, and refer to the allowable tolerance of the actual equipment configuration. Directional consistency: check the difference in probe centre coordinates across each trigger direction; the smaller the better. If it exceeds the tolerance, inspect the assembly. Overhang effect: compare the calibration residuals of the long configuration with those of the short configuration; the differences should be explainable. Looseness point: check the data drift after repeated assembly; if the drift is unacceptable, the assembly is rejected. The first two are already covered by routine calibration; the last two require extra attention after adding adaptors. There is no standard tolerance value for the overhang effect. The usual practice is to calibrate the same stylus in both the native thread and adaptor configurations, then compare the residuals; the difference should be within the equipment’s repeatability. The looseness point is more straightforward: if the data drifts consistently in one direction after repeated assembly, the mating surfaces are suspect, and that combination must not be released.
Release criteria — check three items: calibration data is stable after repeated assembly; multi-directional triggering consistency is within tolerance; and the difference between actual measurement results and the baseline configuration (without the adaptor) is explainable and reproducible. If all three are met, this adaptor configuration can be included in the process documentation, but it must be noted in the document as an adaptor configuration and accompanied by calibration records. Subsequent operator changes, shift changes, or batch changes should all be reproduced according to these records.
Any of the following conditions requires rejection: calibration data drifts after repeated assembly; multi-directional triggering consistency exceeds tolerance and cannot be resolved by adjusting the assembly; the difference between actual measurement results and the baseline configuration cannot be explained; or the adaptor itself lacks traceable part numbers and specification records. The last point is especially important — if the adaptor’s source and specifications are unclear, no matter how thorough the calibration, long-term stability cannot be guaranteed. The styli in the catalogue have seven fields: part number, material, L, D, S, EWL, and W. Adaptors and extension bars should likewise have corresponding verifiable specifications, based on the official data sheet. Adaptors without traceable specifications are not recommended for use on the production line.
Calibration records should include at least: a combination description (following the naming convention in the catalogue, e.g. M3-Stylus (R-3-SS-1.5-L21) plus the adaptor part number), assembly date, calibration date, number of repeated assemblies, stylus tip diameter and probe centre coordinates for each calibration, acceptance result, and operator. Records can be kept in a table or in the device’s built-in calibration log; the key is traceability and repeatability. If data drift occurs later, the records will show exactly which assembly or calibration introduced the variation.
Using an adaptor is not a problem, but it does require a few extra steps and more checks. If these steps are done properly, an adaptor-based configuration can be used in process documentation just like a native configuration. If not, the adaptor becomes an unclear source of error in the data.
It can be fitted, but you need to understand the trade-offs. Every adaptor added introduces another joint face, extra overhang, and a potential point of loosening, which reduces the rigidity of the stylus chain and makes calibration more complex. The official selection guidance consistently stresses using the shortest stylus that meets the application and minimising the number of joints. Adaptors are therefore only suitable for temporary fixes or low-accuracy work, such as rough probing, tool setting, or datum setting—tasks that do not feed into the final report. If this batch of M3 styli is intended for long-term use on an M2 probe head for formal measurement, the more robust approach is to switch to M2 styli directly rather than relying on adaptors to cover the specification.
Both options carry a penalty; neither is inherently more cost-effective. The penalty does not depend on thread size, but on how many extra joint faces and how much additional overhang you introduce. M2 to M3 typically means mounting a small-thread stylus on a large-thread probe head. The stylus itself is slender, and adding an adaptor increases overhang and moves the bending point further out. M3 to M4 is common in on-machine probing or high-rigidity applications such as the TP7M, where the design is already optimised for stiffness and weight; adding an adaptor cancels out those benefits. There is only one criterion: after adding the adaptor, does the total overhang and number of joints in the stylus chain still meet the tolerance requirements of the workpiece? Refer to the official data sheet for the final answer.
Yes, and it must be recalculated. EWL is defined as the distance from the centre of the stylus tip to the point where the stylus stem would interfere with the feature being measured; total length L is measured from the mounting face to the tip centre. Adding an adaptor changes the mounting face position, and part of the exposed stylus stem may also be shielded by the adaptor, so the original L and EWL values no longer apply. The correct procedure is to re-measure the actual length and interference point of the entire stylus chain after the adaptor is fitted, then calibrate the probe and write the new tip centre position and equivalent diameter into the program. If the old parameters are kept, the measured dimensions will shift systematically, and this error will not show up in the report—it is most likely to be mistaken for a workpiece out-of-tolerance condition.
It can’t be avoided — in fact, it adds more work. Calibration is essentially about letting the probe know where the stylus tip centre is and what the effective stylus tip diameter is. Once the adaptor is changed, the mating condition of the joint face, the overhang length, and even the tightening torque can all vary, which shifts the stylus tip centre position. So every time you change the adaptor or stylus combination, recalibration is required. If you keep a fixed adaptor set just to avoid calibration, that set becomes a permanent loose point, and repeatability will degrade over time. A more robust approach is to standardise the thread type by probe/probe head model, use the same stylus specification wherever possible, and minimise adaptors — this actually reduces the number of calibrations.
Three scenarios are acceptable. First, temporary emergencies: if the proper stylus has not arrived, an adaptor can be used for rough measurement, alignment, and tool setting — but not for final reporting. Second, low-accuracy operations: where tolerances are wide, probe triggering is sufficient, and repeatability is not critical. Third, bench or fixture debugging: to run the program through before formal measurement and quickly try different stylus tip diameters with adaptors. The rule of thumb is: adaptors should only be used where extra overhang and looseness can be tolerated. Once you move into the formal dimensional chain — especially for key characteristics — switch back to the native stylus specification. Refer to the official data sheet.
The order is: identify the probe/probe head model first, then determine the thread, and only then select the stylus ball diameter and length. Identify the probe first, then the thread — don’t follow the machine brand. Many domestic CMMs and some Mitutoyo models use the Renishaw system for their probe heads and controllers, so you can’t infer the thread simply from “I have brand XX”. Check the official catalogue: TP2, TP20, TP200 and REVO use M2; TP1, TP6, SP25M and REVO use M3; TP7M and on-machine probing use M4. The Equator comparator uses M2 with the TM25-20 and M3 with the SM25-2. If you’re unsure, check the probe nameplate or refer to the official data sheet — don’t guess.
Back to the original question: can an M3 screw be threaded into an M2 hole? The answer is yes, but first delete the word “can” from your mind and replace it with “is it worth it”. An adaptor is not a universal fix — it simply moves the size problem to another location, from thread specification to strength, service life and assembly risk. What really decides whether to do it is not whether you have an adaptor on hand, but who goes to the site, how long the machine is down, and how much is lost when the equipment fails.
Here is a decision rule you can use tomorrow: first ask “what is the worst consequence if this screw fails”, then decide whether an adaptor is acceptable. If the worst case is “unscrew it and reinstall”, then an adaptor is fine and the cost is manageable. If the worst case is “machine downtime, dropped parts, personal injury, or scrapping a whole batch”, then don’t adapt — re-machine the hole, replace the part, or redesign instead. Writing this rule into your assembly process sheet will serve you better than memorising any thread conversion table.
Three practical points to keep in mind: first, mark every adaptor position separately on the drawing so it is not mistaken for a standard fastening point and copied later; second, calculate the torque at the adaptor point to the lower of the two ratings, not the higher; third, run a disassembly–reassembly cycle test before mass production — only an adaptor that survives ten cycles is qualified for the production line.
Threads are the most unremarkable universal language in the industrial world, and precisely because they are universal, they are the easiest to “translate” casually. But every translation carries loss. Work out that loss before deciding whether to change the wording — that is engineering judgement.
Every machine tool differs in configuration, operating conditions and budget. This article only provides a reference framework. You can:
NINGBO JCE INDUSTRIAL TECHNOLOGY CO., LTD. — 15 years focused on precision measurement, covering selection, installation, calibration, repair and maintenance for the full range of Renishaw, Marposs and Blum-Novotest probes and tool setters.
| Contact Information | Details |
|---|---|
| Official appointment | jcetech.cn/contact |
| Service hotline | 157-5780-7400 / 132-2194-1413 |
| Repair shipping address | Ningbo Yinzhou R&D Park A2-12B17 |
| Service coverage | Nationwide on-site service · 48-hour response for urgent repairs |
Send us your problem and let our engineers help you work out the numbers.
If the criteria or procedures in this article do not match your machine, send us the control system, probe model and a photo of the installation — we will answer with the specific settings rather than a generic recommendation.
| Item | Detail |
|---|---|
| Company | NINGBO JCE INDUSTRIAL TECHNOLOGY CO., LTD. (JCETech) |
| Address | Room 14-1-17, Building 033, Building 2, No. 15, Lane 587 Juxian Road, Juxian Subdistrict, Hi-Tech Zone, Ningbo 315048, Zhejiang, P.R. China |
| Contact | Mr. Li / Mr. Zhang |
| Phone | +86 157-5780-7400 (Mr. Li), +86 132-2194-1413 (Mr. Zhang) |
| Online booking | jcetech.cn/contact |
Repair intake and on-site service use the same address. Please call before shipping a unit so transport and scheduling do not have to be repeated.
Probe, tool setter and laser interferometer repair, calibration and on-machine measurement integration.
157-5780-7400 / 132-2194-1413
打开微信扫一扫,关注「宁波匠测」
获取维修进度查询与技术支持
打开企业微信或微信扫一扫
添加专属顾问,随时沟通